======================================================================
  Microsoft(R) Product Support Services Application Note (Text File)
                WW0981: WINDOWS(TM) 3.11 REFRESH FILES
======================================================================
                                                   Revision Date: 2/94
                                                       1 Disk Included

The following information applies to the version Windows 3.11 update 
for Windows 3.10 users.

-----------------------------------------------------------------------
| INFORMATION PROVIDED IN THIS DOCUMENT AND ANY SOFTWARE THAT MAY     |
| ACCOMPANY THIS DOCUMENT (collectively referred to as an Application |
| Note) IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER      |
| EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED      |
| WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR       |
| PURPOSE. The user assumes the entire risk as to the accuracy and    |
| the use of this Application Note. This Application Note may be      |
| copied and distributed subject to the following conditions:  1) All |
| text must be copied without modification and all pages must be      |
| included;  2) If software is included, all files on the disk(s)     |
| must be copied without modification (the MS-DOS(R)  utility         |
| diskcopy is appropriate for this purpose);  3) All components of    |
| this Application Note must be distributed together;  and  4) This   |
| Application Note may not be distributed for profit.                 |
|                                                                     |
| Copyright (C) 1994 Microsoft Corporation.  All Rights Reserved.     |
| Microsoft and MS-DOS are registered trademarks and Windows is a     |
| trademark of Microsoft Corporation.                                 |
|---------------------------------------------------------------------|


ADDENDUM TO THE MICROSOFT SOFTWARE LICENSE AGREEMENT
====================================================
FOR MICROSOFT WINDOWS OPERATING SYSTEM VERSION 3.10
===================================================

The files provided in this Application Note are intended to replace
the corresponding files provided with Microsoft Windows 3.10. Upon
installation, these files become a part of the Windows operating
system and are subject to the same license terms and conditions as the
Windows 3.10 product you previously acquired from Microsoft
Corporation. Any other use of these files is prohibited.

MICROSOFT WINDOWS VERSION 3.11 FILES
====================================

This Application Note includes updated versions of eight core Windows
3.10 files. To update these files to version 3.11, follow the
procedure below that is appropriate to your configuration.

To update a local installation of Windows 3.10 to Windows 3.11
--------------------------------------------------------------

1. Quit Microsoft Windows.

2. Create a backup directory. For example, to create a backup
   directory off the root of drive C, type MD C:\BACKUP at the MS-DOS
   command prompt and then press ENTER.

3. Copy the files listed below from your Windows SYSTEM subdirectory
   to the backup directory or a floppy disk.

      COMMDLG.DLL
      GDI.EXE
      KRNL386.EXE
      PSCRIPT.DRV
      UNIDRV.DLL
      SHELL.DLL
      USER.EXE

   To do this, use the following syntax

      copy <drive>:\<windir>\system\<filename> <drive>:\<backdir>

   where <drive> is your hard disk drive, <windir> is your Windows
   directory, <filename> is the file you are copying, and <backdir> is
   your backup directory.
   
   For example, if your hard disk drive is C, your Windows directory
   is named WINDOWS, and you are copying COMMDLG.DLL, type the
   following:
   
      copy c:\windows\system\commdlg.dll c:\backup
      
   Repeat this command for the remaining files.

4. Insert the enclosed WW0981 disk in the appropriate floppy disk
   drive. At the MS-DOS command prompt, type the following and then
   press ENTER

      copy <drive>:\*.* <destination>

   where <drive> is your floppy disk drive and <destination> is your
   Windows SYSTEM subdirectory.

   For example:

      copy a:\*.* c:\windows\system

5. If you use Novell NetWare connectivity, do the following:

   a. Use a text editor (such as Windows Notepad) to open your
      SYSTEM.INI file, which is located in your Windows directory.

   b. In the [386Enh] section, change DEVICE=*VTD to DEVICE=VTDA.386.

   c. Save the file and quit the text editor.

To update a network installation of Windows 3.10 to Windows 3.11
----------------------------------------------------------------

1. Determine the location of your SYSTEM.INI file and the network
   share that contains your shared Windows files. For example, if the
   network drive containing your Windows program files is Q, the
   location of your shared Windows files may be Q:\WINSHARE and your
   user directory may be Q:\USER\<YOURNAME> (or your user directory
   may be located on your local hard disk drive).

2. Quit Microsoft Windows.

3. Create a backup directory. For example, to create a backup
   directory off the root of drive C, type MD C:\BACKUP at the MS-DOS
   command prompt and then press ENTER.

4. Copy the following files from the network share to the backup
   directory on your hard disk drive using the following syntax at the
   MS-DOS command prompt and then press ENTER

      copy <netdrive>:\<netshare>\<filename> <harddrive>:\<backdir>
   
   where <netdrive> is the network drive,<netshare> is the network
   share containing your SYSTEM.INI file, <filename> is the file you
   are copying, <harddrive> is your hard disk drive, and <backdir> is
   your backup directory.

   For example, if your network drive is Q, the network share is
   WINSHARE, the file you want to copy is COMMDLG.DLL, your hard disk
   drive is C, and your backup directory is called BACKUP, type the
   following:

      copy q:\winshare\commdlg.dll c:\backup
   
   Repeat this command for the remaining files:

      COMMDLG.DLL
      GDI.EXE
      KRNL386.EXE
      PSCRIPT.DRV
      UNIDRV.DLL
      SHELL.DLL
      USER.EXE

5. Remove the read-only file attributes on the shared Windows files
   using the MS-DOS ATTRIB command.

6. Insert the enclosed WW0981 disk in the appropriate floppy disk
   drive. At the MS-DOS command prompt, type the following and then
   press ENTER

      copy <drive>:\*.* <destination>

   where <drive> is your floppy disk drive and <destination> is the
   network drive and share.

   For example:

      copy a:\*.* q:\winshare

7. Reset the read-only file attributes on the shared Windows files
   using the MS-DOS ATTRIB command.

8. If you use Novell NetWare connectivity, do the following:

   a. Use a text editor (such as Windows Notepad) to open your
      SYSTEM.INI file.

   b. In the [386Enh] section, change DEVICE=*VTD to DEVICE=VTDA.386.

   c. Save the file and quit the text editor.