Print Commander!                   MANUAL                         March, 1993
v 1.03
*****************************************************************************

INTRODUCTION 

Print Commander! is a memory resident* DOS file that allows the user
to configure certain printer functions from the keyboard and screen
without having to touch the printer itself. By pressing the combination
of the Ctrl-Alt-P keys simultaneously, Print Commander! will appear
on the right side of your screen and allow you to stay at the keyboard
and advance or reverse paper position, switch between draft and near
letter quality mode of print, and select which font-- already supported
by your printer-- you wish to use. Then when you are finished, just hit the
escape key and Print Commander! will vanish, leaving you back where you
started.

Print Commander! was designed to run on IBM compatible personal computers
using the Microsoft or IBM (PC) disc operating system (DOS).
Print Commander! was originally written on and for DOS version 5.0 but has
been tested and run successfully on versions 3.3 up to 5.0. It should also
run properly on DOS based systems using graphical interface programs 
(see below under "COMPATIBILITY"), or other operating systems designed to be 
compatible with DOS.

The shareware version of Print Commander!, when resident, occupies
approximately 2.7 kb of conventional memory (hereafter referred to as "RAM")
and a roughly equivalent amount of memory for storage on your hard
disc. This version was written to be compatible with the entire Intel 80x86
family of processors and therefore is not optimized for speed or size.
Registered versions of Print Commander! are coded specifically for the
user's processor, and therefore the registered versions will take up less
disc space, occupy less RAM when resident, and operate faster and more
efficiently than the shareware version (see below).

Print Commander! was designed to be run with dot matrix printers. Most
printers use either Epson or IBM emulation, with Epson being the most 
common of the two. Print Commander! was therefore written to operate in 
Epson emulation mode. This does NOT mean you need to have an Epson Printer.   
Epson/IBM just describes the mode (of software emulation) your printer uses. 
If you are curious, further information can be found in your printer manual.
If your printer uses the IBM emulation exclusively, a compatible version 
of Print Commander! can be provided to you. Please contact us for details.

Print Commander! can be customized for your processor and printer fonts. 
Just load the invoice file (PCOM_INV.TXT) into your word processor 
or a standard ASCII text editor (such as EDIT.COM which comes with DOS 5.0)
and fill in the blanks. If you have additional specific needs not addressed 
in the registration form, or would like to obtain copies of Print Commander! 
for a school, business, or other site, please contact us for rates and to 
discuss your needs.

                                        (continued on next page)













                                   page 2

*****************************************************************************

OPERATION

All Print Commander! files begin with "PCOM" so that your operating system
will keep them together, assuming it categorizes alphabetically. Regardless,
we recommend keeping all files in their own directory, such as C:\PCOM.

Print Commander! is most efficiently loaded by including it in your
AUTOEXEC.BAT. If you are unsure how to do this, please consult your DOS
manual. You can also load Print Commander! from the command line (DOS
prompt) by entering "PCOM_SW" <enter>. You will then be greeting by a short
message verifying that Print Commander! was installed. If you later try
to re-install Print Commander!, you will be informed that it is already 
resident. This feature prevents you from using up precious RAM by accidently
reloading Print Commander!

Once resident, Print Commander! remains silent until activated.              
Simultaneously pressing the combination:

                                 Ctrl-Alt-P

will cause Print Commander! to pop up on your screen.

Print Commander can be called while working at the DOS prompt (command line)
or from within most programs. Some programs, especially those that operate
in a graphic mode (Prodigy, for example), present certain conflicts but
are operable and will produce reliable results when used with Print
Commander! (see below under "COMPATIBILITY").

Once activated and on your screen, Print Commander! has several options
to allow you to control your printer without having to actually change the
printer's settings. On most printers, however, Print Commander! will not be 
allowed (by the printer) to change settings unless you initially turned 
your printer on using the default (probably "draft mode") settings. For 
most users, there is never any need to change the printer's setting except 
through Print Commander!

Here are your choices--                            

        Draft: For fast printing when speed is important and quality
        of type is not.

        Near Letter Quality: Slower, but higher quality print.

        Linefeed: Advances the paper 1 line. Capital (shift) L advances 
        the paper 6 lines.

        Reverse linefeed: Reverse feeds the paper 1 line. Capital (shift) R 
        reverse feeds the paper 6 lines.

        Formfeed: Advances the paper 1 page.

                                        (continued on next page)










                                   page 3

        In the right hand column you may choose different fonts if you first
        selected Near Letter Quality (NL Quality) from the first column.

        There are up to 6 different fonts that may be available to
        you, depending on your printer. If your printer supports only three 
        fonts, there will then be only 3 available to you. In other words, 
        Print Commander! does not create new fonts. It just makes your 
        printer's fonts more easily and readily accessible to you. In the 
        registered version, the actual names of the fonts (such as Courier, 
        Script, Orator, etc.) are used. In this shareware version the user 
        must determine which fonts correspond with which settings by trial 
        and error. This is another good reason to register and obtain a 
        version of the program with fonts specific to your printer!

Examples: Here are two sample font layouts (right hand columns), for the 
        Panasonic 1123 and the Star NX-1000 printers, respectively:


             Print Commander!                      Print Commander!
                   v 1.10                                v 1.10 

             1  Courier                            1  Courier
             2  Prestige                           2  Sanserif
             3  Script                             3  Orator/caps
             4  Bold  PS                           4  Orator

        Other models and other makes of printers will have different fonts
        and a different number of fonts. The Okidata 321 Microline, for
        example, only supports 2 fonts, but the Panasonic 1124 supports 7.

Special Keys: 

        <esc> will exit Print Commander! and restore the page of the host 
        program on which you were working.

        <backspace> will return the printer head to the far left margin.

*****************************************************************************

COMPATIBILITY

We have found that certain software programs give Print Commander! a hard 
time. Here's what we have learned:

        Print Commander! works very well when called from the DOS prompt.
        Some of our users invoke it only when they are working here. But
        Print Commander! was intended to also be used from within other
        (host) programs.

                                        (continued on next page)














                                   page 4

        Almost all text based programs, such as Procomm, Quicken, AskSam,
        the Dosshell, and so on, work perfectly.

        Some Norton products (made by Symantec Corp.) cause distortion of
        certain graphic characters on Print Commander!'s screen. This is
        harmless and does not impair performance of the host program or
        the TSR.

        Many graphic based programs, such as Prodigy and Print Shop,      
        will accept Print Commander! but distort its screen and color 
        pattern. This too seems to be harmless but can also cause the host
        screen to become distorted until a new screen is activated. Again,
        we know of no circumstance where Print Commander! harmed the host
        program, or vice versa.

        Programs in BASIC may present a problem. The text editor bundled
        with DOS 5.0 (EDIT.COM AND QBASIC.EXE) freezes when Print
        Commander! is activated and SHOULD NOT BE USED in this setting.

        Print Commander! will not pop up in Windows. However, there is a
        version of the program that will run quite well with Windows
        and is available FREE OF CHARGE to registered users (see below 
        under "A Word About Shareware").

        Finally some programs, usually word processors, have their own
        built in software to control font selection. In these programs,
        Print Commander! will not be able to configure a font for you.
        Functions in the first column should continue to work normally. 

*****************************************************************************

A WORD ABOUT SHAREWARE

Shareware is a method of marketing, not a kind of software. Shareware is
written by programmers who wish to market their products directly to the
public but may not have the resources to advertise, distribute, and otherwise
promote their products through more traditional retail or wholesale
channels. As with any kind of software, shareware can be either good or bad,
depending on the quality of the product and the needs of the user.
At Sorcerer Software we try to offer only those programs that have 
been thoroughly tested and fill a need for computer users. If you think we  
have been successful please register your copy of Print Commander!

Other reasons to register your shareware with us:             

1) We will send you a version of this program that is written specifically
   for your computer's microprocessor. It will be smaller and faster because 
   it won't have to be compatible with anyone else's computer or printer.

2) Your new program will not be labeled as "Shareware" and will not have
   a "nag" screen. This will reduce the amount of memory the program will
   occupy in RAM and on your hard disc.

                                        (continued on next page)










                                   page 5
                        
3) Your registered Print Commander! copy will be written specifically
   for your printer's make and model. The fonts in the right hand column of
   the screen program will be the fonts YOU use with YOUR printer, not such
   generic fonts as "Font 1" and "Font 2".

4) We will send with your registered version of this program another copy
   of Print Commander! which, instead of being a TSR, can be run as you
   need it from the DOS prompt (command line) and therefore can also be used
   with Windows. It will run in a DOS box with Windows in 386
   Enhanced mode, or as any other DOS program does in Standard mode. Since 
   this copy is not a TSR, it will not take up any of your conventional 
   memory except while it is being used.

5) You will be eligible for discounted upgrades to future releases of
   Print Commander!

6) Being on our mailing list, we can apprise you of other Sorcerer Software
   releases that may interest you and that would operate on your particular
   system.

*****************************************************************************

LEGAL

THIS SOFTWARE AND MANUAL ARE SOLD "AS IS" AND WITHOUT WARRANTIES AS TO
PERFORMANCE OF MERCHANTABILITY OR ANY OTHER WARRANTIES WHETHER EXPRESSED
OR IMPLIED. BECAUSE OF THE VARIOUS HARDWARE AND SOFTWARE ENVIRONMENTS
INTO WHICH THIS PROGRAM MAY BE PUT, NO WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE IS OFFERED. GOOD DATA PROCESSING PROCEDURE DICTATES THAT ANY PROGRAM
BE THOROUGHLY TESTED WITH NON-CRITICAL DATA BEFORE RELYING ON IT. THE USER
MUST ASSUME THE ENTIRE RISK OF USING THE PROGRAM. ANY LIABILITY OF THE
SELLER WILL BE LIMITED EXCLUSIVELY TO PRODUCT REPLACEMENT OR REFUND OF
PURCHASE PRICE.

*****************************************************************************

AND FINALLY...

We would love to hear what you think about Print Commander!, including
any constructive criticism you may have. We plan to make version 2.0
even better!

                                        (continued on next page)





















                                   page 6

Please direct your feedback, special requests, and questions to:

Sorcerer Software
16311 Ventura Blvd., suite #660
Encino, CA 91436

     or

Compuserve 71544,2475

Telephone support is available to registered users.

*****************************************************************************

* A TSR (Terminate-and-Stay-Resident) is a program that, once loaded, 
remains in memory until it is unloaded by the user (an option not available
in the shareware version of this program) or the computer is re-booted or
turned off. Therefore the program (the TSR) can be called immediately,
without having to search the disc, and can be initiated by pressing
specific pre-designated keys (in this case, Ctrl-Alt-P). A TSR can also
be run on top of another (or "host") program. 

Example: While using Procomm Plus and online with another computer (such 
as Compuserve), the user could press Ctrl-Alt-P and see Print Commander! 
pop up on the right side of the screen, assuming DOS is not busy at that 
moment. Computer control is then transferred to Print Commander! The user can 
then configure the printer-- position the paper and select a font, perhaps. 
Press escape at this point and Print Commander! will disappear, leaving the 
user back where he/she was with Procomm Plus and transferring control back 
to Procomm Plus. Isn't that slick?

*****************************************************************************

Thank you for supporting shareware!
