HELP,  Command Quick Reference (CTRL-S to Stop, CTRL-C to Cancel)

&$    HELP, Ampersand Commands       Kn    n=0  Call Duration Mode
%$    HELP, Percent Commands               n=1  Real Time Clock Mode
A/    Repeat Last Command            Mn    n=0  Speaker Off
A>    Continuously Repeat Command          n=1  Speaker On Until CD
AT    Command Mode Prefix                  n=2  Speaker Always On
A     Answer Call                          n=3  Speaker Off During Dial
Bn    n=0  V32 Mode/CCITT Answer Seq On    n=0  Return Online
      n=1  HST Mode/Bell Answer Seq        n=1  Return Online & Retrain
Cn    n=0  Transmitter Off                 n=2  Return Online & Speed Shift
      n=1  Transmitter On            P     Pulse Dial
Dn    Dial a Telephone Number        Qn    n=0  Result Codes Sent
      n=0..9#*TPR,;"W@!()-                 n=1  Quiet (No Result Codes)
DL    Dial Last Phone Number               n=2  Verbose/Quiet On Answer
DSn   Dial Stored Phone Number       Sr=n  Sets Register "r" to "n"
D$    HELP, Dial Commands            Sr?   Query Register "r"
En    n=0  No Command Echo           S$    HELP, S Registers
      n=1  Echo Command Chars        T     Tone Dial
Fn    n=0  Online Echo               Vn    n=0  Numeric Responses
      n=1  No Online Echo                  n=1  Verbal Responses

HELP, Ampersand Commands (CTRL-S to Stop, CTRL-C to Cancel)

&An   n=0  Disable /ARQ Result Codes   &Pn   n=0  N.American Pulse Dial
      n=1  Enable /ARQ Result Codes          n=1  UK Pulse Dial
      n=2  Enable /Modulation Codes    &Rn   n=0  CTS Follows RTS
      n=3  Enable /Extra Result Codes        n=1  Ignore RTS
&Bn   n=0  Floating DTE Speed                n=2  RX to DTE/RTS high
      n=1  Fixed DTE Speed             &Sn   n=0  DSR Always On
      n=2  DTE Speed Fixed When ARQ          n=1  Modem Controls DSR
&Cn   n=0  CD Always On                      n=2  Pulse DSR, CTS=CD
      n=1  Modem Controls CD                 n=3  Pulse DSR
&Dn   n=0  Ignore DTR                  &Tn   n=0  End Test
      n=1  Reserved                          n=1  Analog Loopback (ALB)
      n=2  DTE Controls DTR                  n=3  Digital Loopback (DLB)
&F    Load Factory Configuration             n=4  Grant Remote DLB
&Gn   n=0  No Guard Tone                     n=5  Deny Remote DLB
      n=1  550 Hz Guard Tone                 n=6  Remote Digital Loopback
      n=2  1800 Hz Guard Tone                n=7  Remote DLB With Self Test
&Hn   n=0  Disable TX Flow Control           n=8  ALB With Self Test
      n=1  CTS                         &W    Store Configuration
      n=2  Xon/Xoff                    &Xn   n=0  DCE Synchronous Clock

HELP, Dial Commands (CTRL-S to Stop, CTRL-C to Cancel)

0-9 Digits to Dial
*   Auxiliary Tone Dial Digit
#   Auxiliary Tone Dial Digit
T   Tone Dialing
P   Pulse Dialing
R   Call an Originate Only Modem
,   Pause (Wait for S8 Time)
;   Remain in Command Mode After Dialing
"   Used to Dial Alpha Phone #'s
W   Wait for 2nd Dial Tone (X3-X7)
@   Wait for an Answer (X3-X7)
!   Flash Switch Hook

HELP, S Register Functions (CTRL-S to Stop, CTRL-C to Cancel)

S0  Ring to Answer On                  S19 Inactivity Timeout (min)
S1  Counts # of Rings                  S20 Reserved
S2  Escape Code Char                   S21 Break Length (1/100sec)
S3  Carriage Return Char               S22 Xon Char
S4  Line Feed Char                     S23 Xoff Char
S5  Backspace Char                     S24 DSR Pulse Time (1/50sec)
S6  Wait Time/Dial Tone (sec)          S25 Reserved
S7  Wait Time/Carrier (sec)            S26 RTS/CTS Delay Time (1/100sec)
S8  Comma Time (sec)                   S27 Bit Mapped
S9  Carrier Detect Time (1/10sec)            1 = V21 Mode
S10 Carrier Loss Time (1/10sec)              2 = Disable TCM
S11 Dial Tone Spacing (msec)                 4 = Disable V32
S12 Escape Code Time (1/50sec)               8 = Disable 2100hz
S13 Bit Mapped                              16 = Disable MNP Handshake
      1 = Reset On DTR Loss                 32 = Disable V.42 Detect Phase
      2 = Do Originate in Auto Answer       64 = Reserved
      4 = No Pause Before Result Codes     128 = Unusual SW-Incompatibility
      8 = Do DS0 On DTR                S28 V32 Handshake Time (1/10sec)

