                       DELRINA TECHNOLOGY INC.

        895 Don Mills Road                6830 Via Del Oro
         500-2 Park Centre                    Suite 240
         Toronto, Ontario               San Jose, California
          Canada M3C 1W3                  U.S.A. 95119-1353

                       Product Support Numbers
           BBS:(416)441-2752      WinFax PRO 3.0 Only:(416)441-0921
      Fax Back:(416)443-1614       All Other Products:(416)441-1026
                          Fax:(416)441-0774

======================================================================
                   T E C H N I C A L    N O T E S
               Product: WinFax PRO 3.0, WinFax PRO 2.0
                         Document No.: 2033
                    Document Date: October 7, 1993
======================================================================
Subject: OS/2 v2.0 and v2.1 Operating System--Running WinFax

Situation:
==========
You have a Class 1 or Class 2 Fax/Modem and are running WinFax PRO
under OS/2 v2.0 or v2.1. (When running under OS/2, WinFax PRO has
access to only 1000 interrupts per second, which is not enough for
WinFax to fax at 9600 baud.)

Solution:
=========
There are a number of settings that need to be altered for WinFax PRO 
to function correctly under a WIN-OS/2 v2.0 or v2.1 session:

-   WinFax should be run in a full-screen WIN-OS/2 session, and any
    applications that you wish to fax from must be running in the
    same session.

-   The session that WinFax is running under should be left in the 
    foreground during fax reception or transmission.

-   If you have migrated WinFax from a DOS-based Windows installation, 
    you should reinstall WinFax from a WIN-OS/2 session. This is required
    because the OS/2 migration utility will not transfer all of the 
    configuration information that WinFax needs.

-   Change the following WIN-OS/2 settings:

         IDLE_SENSITIVITY=100
         IDLE_SECONDS=60
         COM_HOLD=ON
         HW_TIMER=ON
         INT_DURING_IO=ON

    Note: Setting IDLE_SENSITIVITY to 100 and IDLE_SECONDS to 60 may 
          reduce system performance, and may not be necessary in all 
          cases. For more information, see your OS/2 manual. 

If you are running an Enhanced Mode Windows session under OS/2 v2.1, 
make the following changes to the [386Enh] section of the SYSTEM.INI
file:

    COMxBUFFER=2048
    COMBOOSTTIM1024E=20
    COMxFIFO=0

    Note: The "x" refers to the COM port that the fax/modem is connected
          to.
If you are using WinFax PRO 3.0 (April 93 or later) with a Class 1 Fax/
Modem and do not have a 16550 UART chip, insert the following lines in the
[General] section of the WINFAX.INI file:

    MaxTxSpeed=7200
    MaxRxSpeed=4800

    Note: This will limit WinFax to sending at 7200 and receiving at 4800.
          Valid entries for MaxTxSpeed are 14400, 12000, 9600, 7200 or 
          4800.
          Valid entries for MaxRxSpeed are 14400, 9600, or 4800.

To operate at higher speeds, you must use a 16550 UART chip. OS/2 v2.1's
serial port driver uses the buffering capability of this UART to increase
the reliability of serial port communications running at 9600 baud or faster.

For more information on migration, Win-OS/2 settings, and SYSTEM.INI 
settings, see your OS/2 manual.

For more information on the 16550 UART chip, see your hardware dealer or 
modem anufacturer.

For more information on your modem Class and WINFAX.INI settings, see your
WinFax PRO 3.0 manual.

For information on determining your release date and updating WinFax PRO
3.0, see Technical Note 2074.

