	      INSTALLATION INSTRUCTIONS FOR OS/2 2.1 DRIVERS FOR:
		    SpeedStar VGA, Super VGA, and Hi-Color
				SpeedStar 24
				SpeedStar 24X
			  SpeedStar Pro ISA and VLB

1.      Boot DOS and run your mode-setting utility.  For the SpeedStar VGA, 
	Super VGA, Hi-Color, and 24, the mode setting utility is VMODE.  For 
	the SpeedStar 24X the mode setting utility is 24XMODE.  For the 
	SpeedStar Pro, the mode setting utility is PROMODE.  Using the mode-
	setting utility, configure your monitor for use with the Diamond card.  
	If you have any questions about the mode-setting, please consult the 
	manual for your Diamond card.  DO NOT RUN THE MODE SETTING UTILITY 
	FROM A DOS SESSION UNDER OS/2!

2.      Boot OS/2.  Open up an OS/2 windowed or full-screen command prompt.  
	From the command prompt, type DSPINSTL, the press Enter.

3.      Put the IBM Display Driver Disk 1 into drive A.  The first screen will 
	allow you to select Primary Display or Secondary Display.  Click on 
	Primary Display, then click on OK.

4.      The next screen will allow you to select the chip type for your video 
	card.  It should automatically select the correct chip, but here are 
	the correct selections anyway:

	SpeedStar VGA, Super VGA, Hi-Color, and SpeedStar 24:  ET4000
	SpeedStar 24X:                                         Western Digital WD90C30
	SpeedStar Pro:                                         Cirrus Logic

	Click on the correct chip type, then click on OK.

5.      The next screen will give you two options, Install Using Defaults For 
	Monitor and Install Using Display Adapter Utility Program.  If you 
	have a SpeedStar Pro ISA, click on Install Using Defaults For Monitor, 
	then click on OK and go to step 7.  If you have any other card, click 
	on Install Using Display Adapter Utility Program, then click on OK.

6.      A standard OS/2 file open window will appear.  The file you are looking 
	for is the mode-setting utility.  Normally, these are found in the 
	following locations:

	SpeedStar VGA, Super VGA, Hi-color:       C:\STAR\UTIL\VMODE.COM
	SpeedStar 24:                             C:\SS24\UTIL\VMODE.COM
	SpeedStar 24X:                            C:\24XMODE.COM
	SpeedStar Pro VLB:                        C:\SSPRO\UTIL\PROMODE.COM

	Once you have the file located, click on OK.  This will return you to 
	the screen with the locate button.  It should now show you the full 
	path to the mode-setting utility, as listed above.  Click at the end 
	of the line, then put a space, followed by the word MONITOR, so that 
	it looks like the following:

	SpeedStar VGA, Super VGA, Hi-color:   C:\STAR\UTIL\VMODE.COM MONITOR
	SpeedStar 24:                         C:\SS24\UTIL\VMODE.COM MONITOR
	SpeedStar 24X:                        C:\24XMODE.COM MONITOR
	SpeedStar Pro VLB:                    C:\SSPRO\UTIL\PROMODE.COM MONITOR

7.      The screen will flash several times as it cycles through some mode 
	changes.  A screen will then come up with a choice of resolutions.  
	Pick one of the resolutions that your card supports, then click OK.

8.      You should now have a box prompting you for a drive.  The disk is 
	already in the drive, so click Install.  The necessary files will be 
	copied over and the necessary configuration files modified.  It will 
	prompt you for the second disk.  When it does, put the Display Driver 
	Disk 2 into your A drive, then click OK.

9.      Once the drivers have been copied over, exit from the OS/2 windowed 
	or full screen command prompt, then shut down OS/2 and reboot.  Your 
	system should now come up in the resolution you chose in step 7.

