Reading messages
----------------

  After activating the message-read command, you will be first shown the
message in the base where your lastread pointer is set to. At the bottom of
the screen, a small prompt line will be shown which will give you the
following options:

   [N]ext Message
          Attempt to go to the next message in the base. If possible, the
          message pointer will be incremented to the next message in the
          area. It will be displayed to you and the prompt line will once
          again be shown to you.

   [P]revious Message
          Attempt to go to the previous message in the area. If possible, the
          message pointer will be decremented to the message preceding the
          one that you just read.

   Enter Message number
          Jump to message number.  Just type the number of the message you
          want to display.

   [R]eply to a message
          This will allow you to enter a reply to the message that you are
          currently reading. For more information on entering messages, see
          the "Writing Messages" topic for more information.

    [A]ll message display
          This will cause EchoDor to start sending you each message without
          pausing.  You can use this function if you wish to "capture" the
          messages for reading offline.  If you wish to stop the sending
          press ANY key and EchoDor will stop at the end of the current
          message.

     [Q]uit to main menu.
          This will bring you back to the EchoDor main menu.

     [K]ill current message
          If the current message is either to or from you, then you will be
          presented with the kill option. The kill option will physically
          erase the message from disk. It will be no longer readable and
          CANNOT BE UN-KILLED.

     [S]ave the message for download
          This command will capture the current message to a file which you
          download.  Download may be available from the Pack Mail section or
          it may be provided as a file in the file areas of your bbs.

     [C]hange current message
          If the current message is either to or from you, then you will also
          be presented with this option. It will allow you to change the
          content of the current message.

     [E]nter a message
          This command will allow you to enter a new message in the current
          area.  For more information see the "Writing messages" topic.

     [M]ine
          This commands will restrict messages to only those that are either
          from you or addressed to you.  When you select [M]ine, Echodor will
          say "Reading only messages To/From You".  The read menu will also
          say "Next Message to you" or "Prior Message to you".  To cancel
          enter [M]ine again.  EchoDor will say "Reading all messages."

Reading Threads
---------------

  A thread is nothing more than a topic being discussed within a message
base. The topics are linked togeather forming a chain of messages.  Because
a single message base may contain many threads the messages of one thread
may be mixed with the messages of another thread.

  EchoDor provides three commands which will allow you to more easily read
threads within a message base.

      + - Read next message in thread.  If the message your reading is part
          of a thread and is not the last message in the thread, this
          command will appear in your menu.  By pressing the plus key (+),
          EchoDor will skip to the next message in the thread.

          Once you begin reading a thread, you can read the next message in
          the thread by pressing the <enter> key.  EchoDor will tell you
          when you reach the last message in the thread.  By pressing
          <enter> key one more time, you will be returned to the message
          where you pressed the plus (+) key.

      - - Read previous message in thread.  If the message your reading is
          part of a thread and is not the first message in the thread, this
          command will appear in your menu.  By pressing the minus key (-),
          EchoDor will skip back to the previous message in the thread.

          Once you being reading backward through a thread, you can read
          the prior message in the thread by pressing the <enter> key.
          EchoDor will tell you when you reach the first message in the
          thread.  By pressing the <enter> key one more time, you will be
          returned to the message where you pressed the minus (-) key.

      * - Reposition to last read message.  When you being reading a thread
          by using the plus key (+) or minus key (-), EchoDor remembers the
          place in the message base where you did this.  By pressing the
          asterisk key (*) you can immediately return to that message.

