#
#	$Id: interfaces,v 4.10 1994/10/28 18:24:25 too Exp $
#
#	Network interface configuration for the AmiTCP/IP
#
#	Copyright  1994 AmiTCP/IP Group,
#	                 Network Solutions Development Inc.
#	                 All rights reserved.
#
# AmiTCP/IP uses the network interface to communicate with SANA-II devices,
# just like DOS uses handlers or filesystems to communicate with exec
# devices.  A network interface is created and configured with `ifconfig'
# utility.  AmiTCP/IP can create several network interfaces for each SANA-II
# device; this is seldom useful, except when two different IP addresses are
# needed for one host or when network has several different framings for IP
# or (for example, ARP has got two different framings for IP).
#
# The Install_AmiTCP installation script depends on the interface
# names defined here, so do not change them.
#
# There is a built-in interface "lo0" in AmiTCP/IP, other interfaces should
# be defined here.
#
# This configuration file is read with template:
# NAME/A, DEV=DEVICE/A/K, UNIT/N/A/K, IPTYPE/N/K, ADDR=ADDRESS/K,
# ARPTYPE=IPARPTYPE/N/K, IPREQ=IPREQUESTS/N/K, ARPREQ=ARPREQUESTS/N/K,
# WRITEREQ=WRITEREQUESTS/N/K, NOTRACKING/S, FILTER/S, NOARP/S,
# P2P=POINT2POINT/S, NOSIMPLEX/S, LOOPBACK/S
#
# Lines can be continued if their last character is '+'. The '#' and ';' are
# comment characters - rest of the line is ignored
#
# Parameters are interpreted as follows:
# NAME/A
#   New-style AmiTCP/IP network interface name. This name must be
#   unique. If you have multiple units for the same device, then you
#   must differentiate the units by adding the unit number as a suffix
#   to the name, for example. The maximum lenght for the name is 15
#   bytes.
# DEV=DEVICE/A/K
#   Sana-II (old-style AmiTCP/IP) device name
# UNIT/N/A/K
#   Sana-II (old-style AmiTCP/IP) device unit number
# ADDR=ADDRESS/K (*
#   Hardware address used by SANA-II device configuration in hexadecimal
#   notation with octets separated by colons,
#   e.g. 80:00:13:AE:45:EF. This should be used if your ethernet adapter
#   has no address ROM, for example.
# IPTYPE/N/K (*
#   Packet type (framing) for Internet Protocol (IP)
# IPREQ=IPREQUESTS/N/K
#   IO requests allocated for receiving IP packets.
# ARPTYPE=IPARPTYPE/N/K (*
#   Packet type (framing) for Address Resolution Protocol (ARP)
# ARPREQ=ARPREQUESTS/N/K
#   IO requests allocated for receiving ARP packets
# WRITEREQ=WRITEREQUESTS/N/K
#   IO requests allocated for transmitting packets
# NOTRACKING/S
#   Disable the packet type tracking on SANA-II devices.  This feature is
#   needed to circumvent a bug in a2060.device V37.2 
# FILTER/S
#   Enable Sana-II packet filtering for this interface. This is needed only
#   if you have several protocol stacks using the same Sana-II device and
#   unit. E.g., Envoy uses IP, too, so the FILTERing should be enabled on
#   interfaces which are shared with Envoy
# NOARP/S
#   Disable the ARP for this interface
# P2P=POINT2POINT/S
#   Use the device as point-to-point device
# NOSIMPLEX/S
#   Disable the copying of broadcast packets.  Set this parameter if we hear
#   our own broadcasts
# LOOPBACK/S
#   Set this parameter if it is loopback
#
# *) Don't set these parameters if you don't know what you are doing.
#    AmiTCP/IP recognizes Ethernet, Arcnet (RFC 1051 framing), SLIP and PPP
#    drivers automatically.  See file <netinclude/net/sana2tags.h> for the
#    packet types used for these drivers.
# 
# Here are few examples:
#
# Serial Line IP
#
slip0 DEV=DEVS:Networks/rhslip.device UNIT=0
# IPTYPE=2048 NOARP P2P IPREQ=8 WRITEREQ=8
#
# SLIP with Van Jacobson header compression 
#
cslip0 DEV=DEVS:Networks/rhcslip.device UNIT=0
# IPTYPE=2048 NOARP P2P IPREQ=8 WRITEREQ=8
#
# Ethernet adapter A2065
#
ether0 DEV=DEVS:Networks/a2065.device UNIT=0
a2065 DEV=DEVS:Networks/a2065.device UNIT=0
# IPTYPE=2048 ARPTYPE=2054 ARPREQ=4 IPREQ=16 WRITEREQ=16 
#
# Hydra Ethernet adapter
#
hydra DEV=DEVS:Networks/hydra.device UNIT=0
#
# GoldenGate WD80xx Ethernet adapter
#
wd80xx DEV=DEVS:Networks/wd80xx.device UNIT=0
# NOTE: This needs an configuration file for the IRQ and MEM address settings!
#
# ASDG EB920 Ethernet adapter
#
eb920 DEV=DEVS:Networks/eb920.device UNIT=0
#
# Village Tronic Ariadne Ethernet adapter
#
ariadne DEV=DEVS:Networks/ariadne.device UNIT=0
#
# GoldenGate 2 Ethernet for 3COM 3c503 card
# NOTE: This needs an configuration file for the IRQ and ISA address settings!
#
gg_3c503 DEV=DEVS:Networks/gg_3c503.device UNIT=0
#
# GoldenGate 2 Ethernet for NE1000 card
# NOTE: This needs an configuration file for the IRQ and ISA address settings!
#
gg_ne1000 DEV=DEVS:Networks/gg_ne1000.device UNIT=0
#
# GoldenGate 2 Ethernet for NE2000 card
# NOTE: This needs an configuration file for the IRQ and ISA address settings!
#
gg_ne2000 DEV=DEVS:Networks/gg_ne2000.device UNIT=0
#
# GoldenGate 2 Ethernet for SMC/WD 80x3 card
# NOTE: This needs an configuration file for the IRQ, 
# IO and BASE address settings!
#
gg_smc DEV=DEVS:Networks/gg_smc.device UNIT=0
# 
# Arcnet adapter a2060 
#
arcnet0 DEV=DEVS:Networks/a2060.device UNIT=0 NOTRACKING 
a2060 DEV=DEVS:Networks/a2060.device UNIT=0 NOTRACKING 
# IPTYPE=240 ARPTYPE=241 ARPREQ=4 IPREQ=16 WRITEREQ=16 
#
# An X.25 driver by Dave Martin
#
ax25 DEV=DEVS:Networks/ax25.device UNIT=0 +
  IPTYPE=204 ARPTYPE=205 ARPREQ=3 IPREQ=16 WRITEREQ=16
#
# Village Tronic Ariadne Liana (PLIP) interface
#
# These entries are not complete! Not enough info now.
#
;liana0 DEV=DEVS:Networks/ariadneliana.device UNIT=0
;liana1 DEV=DEVS:Networks/ariadneliana.device UNIT=1
# EOF
