(P)FCS/WCS Mark II Configuration for FALCON 3.0
(Uses F3SB2.BAT, F3SB2.ADV, and F3SB2.RMP)
By Capt. Stuart Butts, USAF, WPAFB

Air Combat Mode (ACM) (rocker switch up)
-----------------------------------------
(P)FCS
-------
Upper button  = A-A weapons select
Middle button = Radar on/off
Lower button  = ECM on/off
Hat up        = Padlock view - 1st press
                Front view - 2nd press
Hat right     = Right view - press
                Front view - release
Hat left      = Cockpit up/down
Hat down      = Track view - press
                Front view - release
Hat middle    = AWACS navigation information

WCS MarkII
-----------
Button 1       = Dispense flare/chaff 
Button 2       = ACM radar (10x40) - 1st press
                 ACM radar (20x20) - 2nd press
Button 3       = Target select
Button 4       = Clear lock
Button 5       = IFF check
Button 6       = Speedbrakes

Normal Air Mode (NAM) (rocker switch center)
-----------------------------------------
(P)FCS
-------
Upper button  = A-A weapons select
Middle button = Radar on/off
Lower button  = ECM on/off
Hat up        = Padlock view - 1st press
                Front view - 2nd press
Hat right     = Right view - press
                Front view - release
Hat left      = Left view - press
                Front view - release
Hat down      = Target/Missle/Enemy view - press
                Front view - release
Hat middle    = AWACS navigation information

WCS MarkII
-----------
Button 1       = Dispense flare/chaff 
Button 2       = Radar scan distance
Button 3       = Target select
Button 4       = Clear lock
Button 5       = Radar lock/IFF check
Button 6       = Speedbrakes

Ground Attack Mode (GAM) (rocker switch down)
-----------------------------------------
(P)FCS
-------
Upper button  = A-G weapons select
Middle button = Radar on/off
Lower button  = ECM on/off
Hat up        = Padlock view - 1st press
                Front view - 2nd press
Hat right     = Right view - press
                Front view - release
Hat left      = Cockpit up/down
Hat down      = Rear view - press
                Front view - release
Hat middle    = AWACS navigation information

WCS MarkII
-----------
Button 1      = Dispense flare/chaff 
Button 2      = SEA radar (FSX only) - 1st press
                GM radar - 2nd press 
Button 3      = Target select
Button 4      = Clear lock
Button 5      = ILS HUD mode - 1st press
                ILS mode toggle - 2nd press
Button 6      = Speedbrakes

Power Approach Mode (PAM) (rocker switch down - remapped)
-----------------------------------------
(P)FCS
-------
Upper button  = Left view - 1st press
                Front view - 2nd press
Middle button = Wingman view
Lower button  = Chase view - 1st press
                Front view - 2nd press
Hat up        = Padlock view - 1st press
                Front view - 2nd press
Hat right     = Right view - press
                Front view - release
Hat left      = Cockpit up/down
Hat down      = Rear view - press
                Front view - release
Hat middle    = AWACS navigation information

WCS MarkII
-----------
Button 1      = Dispense flare/chaff 
Button 2      = Flaps
Button 3      = Landing gear
Button 4      = Wheel brakes
Button 5      = ILS HUD mode - 1st press
                ILS mode toggle - 2nd press
Button 6      = Speedbrakes

Notes:  1) After the initial toggle to ACM radar (10x40), 
        1st press of button
        2) In ACM mode, I must press the button 2 times each time I 
        want to toggle the ACM radar mode after that.  I have no 
        idea why it does this.
        3) PAM mode is activated by the initial press of button 5 in
        GAM. To exit PAM move the rocker switch to the center position.
        4) After the initial toggle of the ILS HUD mode, 2nd press
        of button 5 in PAM, the next press of this button will turn
        off the ILS HUD mode, however you will still be in PAM. To
        turn on the ILS HUD mode again, simply press button 5 again.
        5) Do not change into and out of PAM a lot.  When I do this 
        it appears that the remap program gets confused and I lose
        all (P)FCS and WCS button functions, as well as the keyboard,
        so I have to cold reboot.
