ÚÂÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
                            ³³³  INSTALLATION  ³³³
                            ÀÁÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÁÙ

         System Requirements.........................................1
         Users With a Hard Disk Drive................................2
         Users With One 3.5" Disk Drive (No Hard Disk)...............3
         Users With 1 HD 5.25" Disk Drive (No Hard Disk).............4
         Users With One 360K (DD) 5.25" Drive (No Hard Disk).........5
         Users With 2 Floppy Disk Drives (No Hard Disk)..............6
         Running the Program.........................................7


    For help on running TOTAL RECALL print the HELP.TXT file.  For more
    information on TOTAL RECALL print the README.TXT file.   To order your
    Registered Version of TOTAL RECALL print the ORDER.TXT file and use it
    as a blank order form.


    1.    System Requirements
    =========================

    To run TOTAL RECALL all you need is an IBM compatible computer, 512K of
    memory, 1 or 2 floppy drives (hard disk recommended but not necessary),
    any kind of monitor or video card, and MS-DOS 2.0 or later.

    1) (You may not need to perform this first step unless you wish to
       optimize your system performance).  You should have a file called
       CONFIG.SYS in your top-level directory (or on the system disk from
       which you boot-up if you don't have a hard drive).  Edit the file
       CONFIG.SYS and add the following two statements to it:

                FILES=20
                BUFFERS=8

       If you don't have a CONFIG.SYS file in your top-level directory,
       copy the one included with the TOTAL RECALL disk.

    2) If you have a CGA monitor, you will have "snow" on your screen unless
       you include the following statement in your AUTOEXEC.BAT file:

                SET CLIPPER= S1;    (Type exactly as shown).

    3) Make sure that the file COMMAND.COM is in the DOS path or in the top
       directory.



    4) If you use memory resident programs or TSRs you may have problems
       running TOTAL RECALL due to its large memory requirements or other
       conflicts.   If so, do not load any memory resident programs at
       boot-up.


    2.    Users With a Hard Disk Drive
    ==================================

    1) Create a working directory, get into that directory, and copy all
       TOTAL RECALL files from the distribution disk to that directory as
       follows:

                C:
                CD..
                MD RECALL
                CD RECALL
                COPY A:*.* *.*

    2) Run the program by typing:

                TR2


    Note: The GO TO DOS option will not work unless you have a system disk
    in the default path.


    3.    Users With One 3.5" Disk Drive (No Hard Disk)
    ===================================================

    Copy the contents of the distribution disk to a working disk and then
    do your work entirely from that disk without any further disk swapping.

    1) Place the original distribution (source) disk in drive A: (or B:).
    2) Type the following:

                COPY A:*.* A:*.*

    3) Swap your working (destination) disk as instructed.


    4.    Users With 1 HD 5.25" Disk Drive (No Hard Disk)
    =====================================================

    Follow the same instructions as for 1.3 above.




    5.    Users With One 360K (DD) 5.25" Drive (No Hard Disk)
    =========================================================

    Load the program from one disk and then use another disk to hold your
    Subject Files.

    1) Make a working copy of the distribution disk as in 1.3 above.
    2) Run the program by typing:

                TR2

    3) Insert the disk that will hold your Subject Files into the drive.
    4) From the CUSTOMIZE menu define your path as A: (or B:).


    6.    Users With 2 Floppy Disk Drives (No Hard Disk)
    ====================================================

    Use drive A: to hold the main program TR2.EXE and to use drive B: to
    hold your SUBJECT FILES.

    1) Copy TR2.EXE to a system disk.  (This is necessary in order for
       the GO TO DOS option to work).  To create a system disk, format a
       disk with:

                FORMAT A:/S

    2) Copy TR2.EXE to the newly created disk.
    3) Insert the new disk into drive A: and start to run by typing:

                A:\TR2

    4) Insert a blank formatted disk into drive B:
    5) Whenever the program asks you for a Path, type

                B:


    7.    Running the Program
    =========================

    1) Run the program by typing:

                TR2

    2) From here on everything is menu-driven and self-explanatory.   Make
       menu selections by a) using arrow keys to move highlight bar to
       choice and pressing RETURN or b) pressing the first letter of desired
       choice.

    3) You can customize the colors and the sound from the CUSTOMIZE MENU.
       Your new set-up will be saved automatically to disk.



    Note the following:
    -------------------

    The following files must be in the same directory as the main TOTAL
    RECALL program (TR2.EXE) that you run or load from:

        TEST.LOG
        CUSTOM2.MEM
        README.TXT
        HELP.TXT
        INSTALL.TXT
        SUBJECTS.TXT

    [Esc] means to press the key marked "Esc".  This will usually quit
    or exit whatever you are doing at the time.

    [^W] means press the key marked "Ctrl" together with the letter W.

       Copyright (c) 1988-1991 by Zoran Sevarlic.  All Rights Reserved.