GLIB(1) LOCAL NAME glib - patch editor and librarian for synthesizers SYNOPSIS glib DESCRIPTION Glib (one syllable) is a text-screen-oriented librarian and patch editor for electronic synthesizers. It is structured in an attempt to make it easy to add support for new synthesizers. Glib presents three types of menu screens: synthesizer selection, patch librarian, and patch editor. However, depending on choices made when glib was compiled, there may be no synthesizer selection menu, or it may be used to select different sub-parts of a single synth, rather than among different synths. From the outermost selection menu you descend to the librarian. If there is no synth selection menu, you see the librarian screen immediately after invoking glib. The librarian part of the program manipulates 1 synth bank of voices (which can be uploaded to or downloaded from the synth), and 3 banks of library voices (which can be read/written to disk). When you exit the librarian and select a different synth, the contents of the library banks and other settings (e.g. midi channel) for each are retained. From the librarian screen you can descend to the patch editor screen to change or create an individual patch for a given synthesizer. Details about using the librarian and the patch editor are given below. The glib distribution includes support files for various PCs -- IBM, Atari ST, Macintosh, Amiga. And you can run glib on Unix (it uses curses), although obviously most Unix machines don't have midi I/O. Trying it out on Unix will give you a feel for what the program does, so you can decide whether or not it's worth the trouble to port it to your midi-capable PC. Or your could edit patch files on a Unix system and download them to a PC. The current version of glib, version 1.6, supports the synthesizers: DX100, TX81, DEP5, DW8000, Roland D-10, Kawaii K1 K5, DX7, and Casio CZ1. Using glib - Moving around Both the librarian and editor parts of glib make use of arrow keys, or h j k l to move the cursor around. (The arrow keys may not work on non-Unix versions, though.) redraws the screen. These keys are #defined in glib.h, so you can change them if you want. To quit from any mode, use q. In the librarian screen, ? gives a command summary. Esc or grave accent key sends an all-notes-off (though the support for arrow keys may interfere with this use of esc ). Using glib - The librarian The screen shows the synth bank on the left, and the current (1 of 3) library bank on the right. A * identifies the `current' voice, and you use the arrow keys to move it around. As soon as you move to a different voice, it is sent to the `edit buffer' of the synth, so it is very easy to roam around and see what each voice sounds like. Commands: b - Cycle through the (3) library banks, displayed on the right side of the screen. c - Set the midi channel for sending/receiving voices. d - Download from the (real) synthesizer, replacing the current contents of the synth bank. D - Download from a file, replacing the current contents of the synth bank. Same as above, except input comes from file instead of the synth. (Implemented only for Unix version.) e - Edit the current voice (see editor description below). f - List the files on the disk. p - Put the yank buffer, replacing the contents of the current voice. q - Quit, going back to `choose a synth'. r - Read a bank of voices from a file, replacing entirely the current library bank. R - Read a bank of voices from a text file (created with the W command). s - Swap the current voice with the yank buffer. 2 swaps is a no-op. t - Transfer all voices, either from the current library bank to the synth bank, or vice versa. u - Upload the current contents of the synth bank to the synth. You are given a choice of sending the entire bank or just the current voice. U - Upload the current contents of the synth bank to a file. Same as above, except output goes to file instead of the synth. (Implemented only for Unix version.) w - Write the current library bank to a file. W - Write the current library bank to an editable text file. This is slow, and is meant for use in some special circumstance - for instance if you changed the binary format of files, you might want to convert your old patches. y - Yank the current voice into the yank buffer, shown in the middle of the screen. Using glib - The editor In the editor part, arrow keys move the cursor among the parameter values. The cursor will only land on parameter values. Once on a parameter value, the following keys will affect it: K - increase value by 1 J - decrease value by 1 I - increase value by 4 M - decrease value by 4 < - decrease value to its minimum > - increase value to its maximum S - assign same value as last assigned These keys are defined in glib.h, and should be changed to suit your own tastes. I'm not thrilled with these choices, myself, but I had to use something, and at least the hand may stay in one place. To change the name of a voice, use `N'. The `auto-note' is played whenever you press the space bar. This is a convenient way of playing a note as soon as you make a change (ie. you can do everything from the computer keyboard). You can change the auto-note parameters (pitch, duration, volume, channel) the same way as all the other parameters. Synthesizers Here is a list of the sample patch files for each synthesizer in the 1.6 release of glib, together with occasional notes on the current implementation. DX100 Sample patches: fact1.dx1 TX81 Sample patches: fact1.t8p fact1.tx8 DEP5 Sample patches: fact1.dp5 DW8000 Sample patches: fact1.dw8 Roland D-10 Sample patches: d10fact.pat d10fact.rsu d10fact.tim d10fact.ton d10fact.tra d10fact.urp Kawaii K1 Sample patches: k1fact.mlt k1fact.sgl Voices are not sent to the K1's edit buffer. For Kawai K1 multi patches, names of single patches referred to are displayed when they can be found in the synth voice bank of the single patches module. The names are updated whenever a new bank of voices is transferred into this bank. Kawaii K5 Sample patches: card1.k5m card1.k5s Editing of voices is not implemented. DX7 Sample patches: n001.dx7 rom1.d7s Some of the parameters on the DX7s editing screen are `multiplexed'. Move the cursor to the `Modulation Wheel' legend, then `increment' and `decrement' this field: the fields below it will cycle through the `Modulation Wheel', `Aftertouch', `Breath Control', `Foot Control', and `MIDI Control' parameters. Casio CZ1 Sample patches: bank1.cz1 The performance parameters given on the lower part of the editing screen, Glib, Portamento, etc., are just there pro forma. In the current version, setting them doesn't accomplish anything. AUTHORS original version for dx100, tx81z, dep5: Tim Thompson, ...twitch!glimmer!tjt Macintosh and dw1000 support: Steve Falco. d10 support: Michael Kesti, mrk@gvgspd.GVG.TEK.COM Amiga and k5 support: Alan Bland, mab@druwy.ATT.COM or att!druwy!mab K1 support and menu mods: Greg Lee, lee@uhccux.uhcc.hawaii.edu DX7 support: Scott Snyder, ssnyder@citjulie.bitnet, ssnyder@juliet.caltech.edu (addresses valid until mid-June) CZ1 support: Mark R. Rinfret, mrr@amanpt1.Newport.RI.US, ...!rayssd!galaxia!amanpt1!mrr arp file requester, Amiga version: Dave Weiler Some of the code was originally written by Steve Frysinger (moss!spf), John Helton, and James Gosling.