/* $Id: aztcd.h,v 1.60 1995/08/09 12:38:12 root Exp root $
 *
 * Definitions for a AztechCD268 CD-ROM interface
 *	Copyright (C) 1994, 1995  Werner Zimmermann
 *
 *	based on Mitsumi CDROM driver by Martin Harriss
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation; either version 2 of the License, or
 *  (at your option) any later version.
 *
 *  This program is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with this program; if not, write to the Free Software
 *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 *  History:	W.Zimmermann adaption to Aztech CD268-01A Version 1.3
 *		October 1994 Email: zimmerma@rz.fht-esslingen.de
 */

/* *** change this to set the I/O port address of your CD-ROM drive*/
#define AZT_BASE_ADDR		0x320

/* Uncomment this, if your CDROM is connected to a Soundwave32-soundcard
   and configure AZT_BASE_ADDR and AZT_SW32_BASE_ADDR */
/*#define AZT_SW32 1
*/

#ifdef AZT_SW32 
#define AZT_SW32_BASE_ADDR       0x220  /*I/O port base address of your soundcard*/
#endif

/* Set this to 1, if you want your tray to be locked, set to 0 to prevent tray 
   from locking */
#define AZT_ALLOW_TRAY_LOCK	1

/*Set this to 1 to allow auto-eject when unmounting a disk, set to 0, if you 
  don't want the auto-eject feature*/
#define AZT_AUTO_EJECT          0

/*Set this to 1, if you want multisession support. Be warned, this function has
not been tested !!!*/
#define AZT_MULTISESSION        1

/*Set this to 1, if you want to use incompatible ioctls for reading in raw and
  cooked mode */
#define AZT_PRIVATE_IOCTLS      1

/*---------------------------------------------------------------------------*/
/*------------nothing to be configured below this line-----------------------*/


/* Increase this if you get lots of timeouts; if you get kernel panic, replace
   STEN_LOW_WAIT by STEN_LOW in the source code */
#define AZT_STATUS_DELAY	400       /*for timer wait, STEN_LOW_WAIT*/
#define AZT_TIMEOUT		8000000   /*for busy wait STEN_LOW, DTEN_LOW*/
#define AZT_FAST_TIMEOUT	10000     /*for reading the version string*/

/* number of times to retry a command before giving up */
#define AZT_RETRY_ATTEMPTS	3

/* port access macros */
#define CMD_PORT		azt_port
#define DATA_PORT		azt_port
#define STATUS_PORT		azt_port+1
#define MODE_PORT		azt_port+2
#ifdef  AZT_SW32                
 #define AZT_SW32_INIT           (unsigned int) (0xFF00 & (AZT_BASE_ADDR*16))
 #define AZT_SW32_CONFIG_REG     AZT_SW32_BASE_ADDR+0x16  /*Soundwave32 Config. Register*/
 #define AZT_SW32_ID_REG         AZT_SW32_BASE_ADDR+0x04  /*Soundwave32 ID Version Register*/
#endif

/* status bits */
#define AST_CMD_CHECK		0x80		/* 1 = command error */
#define AST_DOOR_OPEN		0x40		/* 1 = door is open */
#define AST_NOT_READY		0x20		/* 1 = no disk in the drive */
#define AST_DSK_CHG		0x02		/* 1 = disk removed or changed */
#define AST_MODE                0x01            /* 0=MODE1, 1=MODE2 */
#define AST_MODE_BITS		0x1C		/* Mode Bits */
#define AST_INITIAL		0x0C		/* initial, only valid ... */
#define AST_BUSY		0x04		/* now playing, only valid
						   in combination with mode
						   bits */
/* flag bits */
#define AFL_DATA		0x02		/* data available if low */
#define AFL_STATUS		0x04		/* status available if low */
#define AFL_OP_OK		0x01		/* OP_OK command correct*/
#define AFL_PA_OK		0x02		/* PA_OK parameter correct*/
#define AFL_OP_ERR		0x05		/* error in command*/
#define AFL_PA_ERR		0x06		/* error in parameters*/
#define POLLED			0x04		/* polled mode */

/* commands */
#define ACMD_SOFT_RESET		0x10		/* reset drive */
#define ACMD_PLAY_READ		0x20		/* read data track in cooked mode */
#define ACMD_PLAY_READ_RAW      0x21		/* reading in raw mode*/
#define ACMD_SEEK_TO_LEADIN     0x31		/* seek to leadin track*/
#define ACMD_GET_ERROR		0x40		/* get error code */
#define ACMD_GET_STATUS		0x41		/* get status */
#define ACMD_GET_Q_CHANNEL      0x50		/* read info from q channel */
#define ACMD_EJECT		0x60		/* eject/open tray */
#define ACMD_CLOSE              0x61            /* close tray */
#define ACMD_LOCK		0x71		/* lock tray closed */
#define ACMD_UNLOCK		0x72		/* unlock tray */
#define ACMD_PAUSE		0x80		/* pause */
#define ACMD_STOP		0x81		/* stop play */
#define ACMD_PLAY_AUDIO		0x90		/* play audio track */
#define ACMD_SET_VOLUME		0x93		/* set audio level */
#define ACMD_GET_VERSION	0xA0		/* get firmware version */
#define ACMD_SET_DISK_TYPE	0xA1		/* set disk data mode */

#define MAX_TRACKS		104

struct msf {
	unsigned char	min;
	unsigned char	sec;
	unsigned char	frame;
};

struct azt_Play_msf {
	struct msf	start;
	struct msf	end;
};

struct azt_DiskInfo {
	unsigned char	first;
	unsigned char	last;
	struct msf	diskLength;
	struct msf	firstTrack;
        unsigned char   multi;
        struct msf      lastTrack;
        unsigned char   xa;
        unsigned char   audio;
};

struct azt_Toc {
	unsigned char	ctrl_addr;
	unsigned char	track;
	unsigned char	pointIndex;
	struct msf	trackTime;
	struct msf	diskTime;
};