; Collection of assembler support routines for NOS
; Copyright 1991 Phil Karn, KA9Q

	.MODEL	MEMMOD,C
	LOCALS
	%MACS
	.LALL
	extrn	ctick:proc
	public	eoi

; Hardware vector for timer linkage
; We use the timer hardware channel here instead of the indirect BIOS
; channel (1ch) because the latter is sluggish when running under DoubleDos
TIMEVEC	EQU	08h

	.DATA
	public	Intstk,Stktop,Spsave,Sssave,Mtasker,Hashtab
	extrn	Isat:word
Spsave	dw	?		; Save location for SP during interrupts
Sssave	dw	?		; Save location for SS during interrupts
Intstk	dw	512 dup(?)	; Interrupt working stack
Stktop	equ	$		; SP set here when entering interrupt
Mtasker	db	?		; Type of higher multitasker, if any
Hashtab	db	256 dup(?)	; Modulus lookup table for iphash()
	.CODE
dbase	dw	@Data
jtable	dw	l0,l1,l2,l3,l4,l5,l6,l7,l8,l9,l10,l11,l12,l13,l14,l15	

; Re-arm 8259 interrupt controller(s)
; Should be called just after taking an interrupt, instead of just
; before returning. This is because the 8259 inputs are edge triggered, and
; new interrupts arriving during an interrupt service routine might be missed.
eoi	proc
	cmp	Isat,1
	jnz	@@1		; Only one 8259, so skip this stuff
	mov	al,0bh		; read in-service register from
	out	0a0h,al		; secondary 8259
	nop			; settling delay
	nop
	nop
	in	al,0a0h		; get it
	or	al,al		; Any bits set?
	jz	@@1		; nope, not a secondary interrupt
	mov	al,20h		; Get EOI instruction
	out	0a0h,al		; Secondary 8259 (PC/AT only)
@@1:	mov	al,20h		; 8259 end-of-interrupt command
	out	20h,al		; Primary 8259
	ret
eoi	endp

; common routine for interrupt return
	public	doret
	label	doret	far
	pop	es
	pop	di
	pop	si
	pop	bp
	pop	dx
	pop	cx
	pop	bx
	pop	ax
	mov	ss,Sssave
	mov	sp,Spsave	; restore original stack context
	pop	ds
	iret

; istate - return current interrupt state
	public	istate
istate	proc
	pushf
	pop	ax
	and	ax,200h
	jnz	@@1
	ret
@@1:	mov	ax,1
	ret
istate	endp

; dirps - disable interrupts and return previous state: 0 = disabled,
;	1 = enabled
	public dirps
dirps	proc
	pushf			; save flags on stack
	pop	ax		; flags -> ax
	and	ax,200h		; 1<<9 is IF bit
	jz	@@1		; ints are already off; return 0
	mov	ax,1
	cli			; interrupts now off
@@1:	ret
dirps	endp

; restore - restore interrupt state: 0 = off, nonzero = on
	public	restore
restore	proc
	arg is:word
	test	is,0ffffh
	jz	@@1
	sti
	ret
@@1:	cli	; should already be off, but just in case...
	ret
restore	endp


; multitasker types
NONE		equ	0
DOUBLEDOS	equ	1
DESQVIEW	equ	2
WINDOWS3	equ	3

; Relinquish processor so other task can run
	public	giveup
giveup	proc
	pushf		;save caller's interrupt state
	sti		;re-enable interrupts
	cmp	mtasker, DOUBLEDOS
	jnz	@@1
	mov	al,2	; 110 ms
	mov	ah,0eeh
	int	21h
	popf		; restore caller's interrupt state
	ret

@@1:	cmp	mtasker, DESQVIEW
	jnz	@@2
	mov	ax, 1000h
	int	15h
	popf		; restore interrupts
	ret

@@2:	cmp	mtasker, WINDOWS3
	jnz	@@3
	mov	ax, 1680h
	int	2fh
	cmp	al, 80h	; call supported?
	jz	@@3	; nope
	popf		; yes - restore interrupts
	ret

@@3:	hlt		; wait for an interrupt
	popf		; restore interrupts
	ret
giveup	endp

; check for a multitasker running
	public	chktasker
chktasker	proc
	mov	mtasker,NONE

	; Check for Microsoft Windows
	mov	ax,1600h
	int	2fh
	cmp	al, 00h		; 0 means windows multitasking not running
	jz	@@4
	cmp	al, 80h		; ditto for 80h return
	jz	@@4
	mov	mtasker, WINDOWS3
	ret

	; Check for DoubleDos
@@4:	mov	ah,0e4h
	int	21h
	cmp	al,1
	jz	@@1
	cmp	al,2
	jnz	@@2
@@1:	mov	mtasker, DOUBLEDOS
	ret

	; Check for DESQVIEW
@@2:	mov	ax, 2b01h
	mov	cx, 4445h
	mov	dx, 5351h
	int	21h
	cmp	al, 0ffh
	jnz	@@3
	ret

@@3:	mov	mtasker, DESQVIEW
	ret
chktasker	endp

; getss - Read SS for debugging purposes
	public	getss
getss	proc
	mov	ax,ss
	ret
getss	endp

; clockbits - Read low order bits of timer 0 (the TOD clock)
; This works only for the 8254 chips used in ATs and 386s.
;
; The timer runs in mode 3 (square wave mode), counting down
; by twos, twice for each cycle. So it is necessary to read back the
; OUTPUT pin to see which half of the cycle we're in. I.e., the OUTPUT
; pin forms the most significant bit of the count. Unfortunately,
; the 8253 in the PC/XT lacks a command to read the OUTPUT pin...
;
; The PC's clock design is soooo brain damaged...

	public	clockbits
clockbits	proc
	mov	al,0c2h	; latch timer 0 count and status for reading
	pushf
	cli		; make chip references atomic
	out	43h,al	; send latch command
	in	al,40h	; get status of timer 0
	mov	bl,al	; save status
	in	al,40h	; get lsb of count
	mov	ah,al	; save lsb
	in	al,40h	; get msb of count
	popf		; no more chip references
	xchg	ah,al	; ax = count in correct order
	shr	ax,1	; count /= 2
	and	bl,80h	; we're only interested in the OUT bit
	or	ah,bl	; combine with OUT bit as most sig bit of count
	ret
clockbits	endp

; Internet checksum subroutine
; Compute 1's-complement sum of data buffer
; Uses an unwound loop inspired by "Duff's Device" for performance
;
; Called from C as
; unsigned short
; lcsum(buf,cnt)
; unsigned short *buf;
; unsigned short cnt;
	public	lcsum
lcsum	proc
	arg	buf:ptr,cnt:word

	if	@Datasize NE 0
		uses	ds,si
		lds	si,buf	; ds:si = buf
	else
		uses	si
		mov	si,buf	; ds:si = buf (ds already set)
	endif

	mov	cx,cnt		; cx = cnt
	cld			; autoincrement si
	mov	ax,cx
	shr	cx,1		; cx /= 16, number of loop iterations
	shr	cx,1
	shr	cx,1
	shr	cx,1

	inc	cx		; make fencepost adjustment for 1st pass
	and	ax,15		; ax = number of words modulo 16
	shl	ax,1		; *=2 for word table index
	lea	bx,jtable	; bx -> branch table
	add	bx,ax		; index into jump table
	clc			; initialize carry = 0
	mov	dx,0		; clear accumulated sum
	jmp	word ptr cs:[bx]	; jump into loop

; Here the real work gets done. The numeric labels on the lodsw instructions
; are the targets for the indirect jump we just made.
;
; Each label corresponds to a possible remainder of (count / 16), while
; the number of times around the loop is determined by the quotient.
;
; The loop iteration count in cx has been incremented by one to adjust for
; the first pass.
; 
deloop:	lodsw
	adc	dx,ax
l15:	lodsw
	adc	dx,ax
l14:	lodsw
	adc	dx,ax
l13:	lodsw
	adc	dx,ax
l12:	lodsw
	adc	dx,ax
l11:	lodsw
	adc	dx,ax
l10:	lodsw
	adc	dx,ax
l9:	lodsw
	adc	dx,ax
l8:	lodsw
	adc	dx,ax
l7:	lodsw
	adc	dx,ax
l6:	lodsw
	adc	dx,ax
l5:	lodsw
	adc	dx,ax
l4:	lodsw
	adc	dx,ax
l3:	lodsw
	adc	dx,ax
l2:	lodsw
	adc	dx,ax
l1:	lodsw
	adc	dx,ax
l0:	loop	deloop		; :-)

	adc	dx,0		; get last carries
	adc	dx,0
	mov	ax,dx		; result into ax
	xchg	al,ah		; byte swap result (8088 is little-endian)
	ret
lcsum	endp

; Link timer handler into timer chain
; Arg == address of timer handler routine
; MUST be called exactly once before uchtimer is called!

toff	dw	?		; save location for old vector
tseg	dw	?		;  must be in code segment

	public	chtimer
chtimer	proc
	arg	vec:far ptr
	uses	ds

	mov	ah,35h		; get current vector
	mov	al,TIMEVEC
	int	21h		; puts vector in es:bx
	mov	cs:tseg,es	; stash
	mov	cs:toff,bx

	mov	ah,25h
	mov	al,TIMEVEC
	lds	dx,vec		; ds:si = vec

	int	21h		; set new vector
	ret
chtimer	endp

; unchain timer handler from timer chain
; MUST NOT be called before chtimer!
	public	uchtimer
uchtimer	proc
	uses	ds

	mov	ah,25h
	mov	al,TIMEVEC
	mov	dx,toff
	mov	ds,tseg
	int	21h		; restore old vector
	ret
uchtimer	endp

; Clock tick interrupt handler. Note the use of "label" rather than "proc"
; here, necessitated by the fact that "proc" automatically generates BP-saving
; code that we don't want here.

	public	btick
	label	btick	far

	pushf
	push	ds
	cli
	mov	ds,cs:dbase	; establish interrupt data segment

	mov	Sssave,ss	; stash user stack context
	mov	Spsave,sp

	mov	ss,cs:dbase
	lea	sp,Stktop

	push	ax		; save user regs on interrupt stack
	push	bx
	push	cx
	push	dx
	push	bp
	push	si
	push	di
	push	es

	call	ctick

 	pop	es
	pop	di
	pop	si
	pop	bp
	pop	dx
	pop	cx
	pop	bx
	pop	ax
	mov	ss,Sssave
	mov	sp,Spsave	; restore original stack context
	pop	ds
	popf
	jmp	dword ptr [toff]		; link to previous vector

; Convert 32-bit int in network order to host order (dh, dl, ah, al)
; Called from C as
; int32 get32(char *cp);

	public	get32
get32	proc
	arg	cp:ptr
	if	@Datasize NE 0
		uses	ds,si
		lds	si,cp	; ds:si = cp
	else
		uses	si
		mov	si,cp	; ds:si = cp (ds already set)
	endif

	cld
	lodsw
	mov	dh,al	; high word to dx, a-swapping as we go
	mov	dl,ah
	lodsw
	xchg	al,ah	; low word stays in ax, just swap
	ret
get32	endp

; Convert 16-bit int in network order to host order (ah, al)
; Called from C as
; int16 get16(char *cp);

	public	get16
get16	proc
	arg	cp:ptr
	if	@Datasize NE 0
		uses	ds,si
		lds	si,cp	; ds:si = cp
	else
		uses	si
		mov	si,cp	; ds:si = cp (ds already set)
	endif

	lodsw		; note: direction flag is don't-care
	xchg	al,ah	; word stays in ax, just swap
	ret
get16	endp

; Convert 32-bit int to network order, returning new pointer
; Called from C as
; char *put32(char *cp,int32 x);

	public	put32
put32	proc
	arg	cp:ptr,x:dword
	if	@Datasize NE 0
		uses	ds,di
		les	di,cp	; es:di = cp
		mov	ax,ss	; our parameter is on the stack, and ds might not
		mov	ds,ax	;   be pointing to ss.
	else
		uses	di
		mov	di,cp	; es:di = cp
		mov	ax,ds	; point es at data segment
		mov	es,ax
	endif

	cld
	mov	ax,word ptr (x+2)	; read high word of machine version
	xchg	ah,al			; swap bytes
	stosw				; output in network order
	mov	ax,word ptr x		; read low word of machine version
	xchg	ah,al			; swap bytes
	stosw				; put in network order

	mov	ax,di	; return incremented output pointer
	if	@Datasize NE 0
		mov	dx,es	; upper half of pointer
	endif
	ret
put32	endp

; Convert 16-bit int to network order, returning new pointer
; Called from C as
; char *put16(char *cp,int16 x);

	public	put16
put16	proc
	arg	cp:ptr,x:word
	uses	di
	if	@Datasize NE 0
		les	di,cp	;es:di = cp
	else
		mov	di,cp	; es:di = cp
		mov	ax,ds
		mov	es,ax
	endif
	cld
	mov	ax,x	; fetch source word in machine order
	xchg	ah,al	; swap bytes
	stosw		; save in network order
	mov	ax,di	; return new output pointer to user
	if	@Datasize NE 0
		mov	dx,es	; upper half of pointer
	endif
	ret
put16	endp

; kbraw - raw, nonblocking read from console
; If character is ready, return it; if not, return -1
	public	kbraw
kbraw	proc
	mov	ah,06h	; Direct Console I/O
	mov	dl,0ffh	; Read from keyboard
	int	21h	; Call DOS
	jz	@@1	; zero flag set -> no character ready
	mov	ah,0	; valid char is 0-255
	ret
@@1:	mov	ax,-1	; no char, return -1
	ret
kbraw	endp

if	@CPU AND 2
; fast I/O buffer routines
; version for 80186, 286, 386 (uses ins, outs instructions)

; outbuf - put a buffer to an output port
	public	outbuf
outbuf	proc
	arg	port:word,buf:ptr,cnt:word
	if	@Datasize NE 0
		uses	ds,si
		lds	si,buf	; ds:si = buf
	else
		uses	si
		mov	si,buf	;ds:si = buf (ds already set)
	endif
	mov	dx,port
	mov	cx,cnt
	cld
	rep outsb		; works only on PC/AT (80286)
	mov	dx,ds
	mov	ax,si		; return pointer just past end of buffer
	ret
outbuf	endp

; inbuf - get a buffer from an input port
	public	inbuf
inbuf	proc
	arg	port:word,buf:ptr,cnt:word
	uses	di
	if	@Datasize NE 0
		les	di,buf		; es:di = buf
	else
		mov	di,buf		; es:di = buf
		mov	ax,ds
		mov	es,ax
	endif
	mov	dx,port
	mov	cx,cnt
	cld
	rep insb		; works only on PC/AT (80286)
	mov	dx,es
	mov	ax,di		; return pointer just past end of buffer
	ret
inbuf	endp

else

; fast buffer I/O routines
; version for 8086/8

; outbuf - put a buffer to an output port
	public	outbuf
outbuf	proc
	arg	port:word,buf:ptr,cnt:word
	if	@Datasize NE 0
		uses	ds,si
		lds	si,buf	; ds:si = buf
	else
		uses	si
		mov	si,buf	; ds:si = buf (ds already set)
	endif

	mov	dx,port
	mov	cx,cnt
	cld

; If buffer doesn't begin on a word boundary, send the first byte
	test	si,1	; (buf & 1) ?
	jz	@@even ; no
	lodsb		; al = *si++;
	out	dx,al	; out(dx,al);
	dec	cx	; cx--;
	mov	cnt,cx	; save for later test
@@even:
	shr	cx,1	; cx = cnt >> 1; (convert to word count)
; Do the bulk of the buffer, a word at a time
	jcxz	@@nobuf	; if(cx != 0){
@@deloop:
	lodsw		; do { ax = *si++; (si is word pointer)
	out	dx,al	; out(dx,lowbyte(ax));
	mov	al,ah
	out	dx,al	; out(dx,hibyte(ax));
	loop	@@deloop	; } while(--cx != 0); }
; now check for odd trailing byte
@@nobuf:
	mov	cx,cnt
	test	cx,1
	jz	@@cnteven
	lodsb		; al = *si++;
	out	dx,al
@@cnteven:
	mov	dx,ds
	mov	ax,si		; return pointer just past end of buffer
	ret
outbuf	endp

; inbuf - get a buffer from an input port
	public	inbuf
inbuf	proc
	arg port:word,buf:ptr,cnt:word
	uses	di
	if	@Datasize NE 0
		les	di,buf	; es:di = buf
	else
		mov	di,buf	; es:di = buf
		mov	ax,ds
		mov	es,ax
	endif
	mov	dx,port
	mov	cx,cnt
	cld

; If buffer doesn't begin on a word boundary, get the first byte
	test	di,1	; if(buf & 1){
	jz	@@bufeven ;
	in	al,dx	; al = in(dx);
	stosb		; *di++ = al
	dec	cx	; cx--;
	mov	cnt,cx	; cnt = cx; } save for later test
@@bufeven:
	shr	cx,1	; cx = cnt >> 1; (convert to word count)
; Do the bulk of the buffer, a word at a time
	jcxz	@@nobuf	; if(cx != 0){
@@deloop:
	in	al,dx	; do { al = in(dx);
	mov	ah,al
	in	al,dx	; ah = in(dx);
	xchg	al,ah
	stosw		; *si++ = ax; (di is word pointer)
	loop	@@deloop	; } while(--cx != 0);
; now check for odd trailing byte
@@nobuf:
	mov	cx,cnt
	test	cx,1
	jz	@@cnteven
	in	al,dx
	stosb		; *di++ = al
@@cnteven:
	mov	dx,es
	mov	ax,di		; return pointer just past end of buffer
	ret
inbuf	endp

endif

	public	longdiv

; long unsigned integer division - divide an arbitrary length dividend by
; a 16-bit divisor. Replaces the dividend with the quotient and returns the
; remainder. Called from C as
;
; unsigned short
; longdiv(unsigned short divisor,int cnt,unsigned short *dividend);
;
;Register usage:
; di - divisor
; si - pointer into dividend array
; cx - loop counter, initialized to the number of 16-bit words in the dividend
; ax - low word of current dividend before each divide, current quotient after
; dx - remainder from previous divide carried over, becomes high word of
;      dividend for next divide

longdiv	proc
	arg	divisor:word,cnt:word,dividend:ptr
	if	@Datasize NE 0
		uses	ds,si,di
		lds	si,dividend
	else
		uses	si,di
		mov	si,dividend	;si -> dividend array
	endif

	cmp	divisor,0		; divisor == 0?
	jne	@2			; no, ok
	xor	ax,ax			; yes, avoid divide-by-zero trap
	jmp	short @1

@2:	mov	dx,0			; init remainder = 0
	mov	cx,cnt			; init cnt
	mov	di,divisor		; cache divisor in register

@@deloop:
	mov	ax,word ptr [si]	; fetch current word of dividend
	cmp	ax,0			; dividend == 0 ?
	jne	@7			; nope, must do division
	cmp	dx,0			; remainder also == 0?
	je	@4			; yes, skip division, continue

@7:	div	di			; do division
	mov	word ptr [si],ax	; save quotient

@4:	inc	si			; next word of dividend
	inc	si
	loop 	@@deloop

	mov	ax,dx			; return last remainder
@1:	ret

longdiv	endp

; long unsigned integer multiplication - multiply an arbitrary length
; multiplicand by a 16-bit multiplier, leaving the product in place of
; the multipler, returning the carry. Called from C as
;
; unsigned short
; longmul(unsigned short multiplier,int cnt,unsigned short *multiplier);
;
; Register usage:
; di = multiplier
; si = pointer to current word of multiplicand
; bx = carry from previous round
; cx = count of words in multiplicand
; dx,ax = scratch for multiply

	public longmul
longmul	proc	far
	arg	multiplier:word,n:word,multiplicand:ptr
	if	@Datasize NE 0
		uses	ds,si,di
		lds	si,multiplicand
	else
		uses	si,di
		mov	si,multiplicand	; si -> multiplicand array
	endif

	mov	di,multiplier		; cache multiplier in register
	xor	bx,bx			; init carry = 0
	mov	cx,n			; fetch n
	mov	ax,cx
	shl	ax,1			; *2 = word offset
	add	si,ax			; multiplicand += n

@@deloop:
	dec	si
	dec	si			; work from right to left
	mov	ax,word ptr [si]	; fetch current multiplicand
	or	ax,ax			; skip multiply if zero
	jz	@@nomult
	mul	di			; dx:ax <- ax * di
@@nomult:
	add	ax,bx			; add carry from previous multiply
	mov	word ptr [si],ax	; save low order word of product
	mov	bx,0			; clear previous carry, leaving CF alone
	adc	bx,dx			; save new carry
	xor	dx,dx			; clear in case we skip the next mult
	loop	@@deloop

	mov	ax,bx			; return final carry
	ret
longmul	endp

ifdef	notdef
; divide 32 bits by 16 bits, returning both quotient and remainder
; This allows C programs that need both to avoid having to do two divisions
;
; Called from C as
;	long divrem(dividend,divisor)
;	long dividend;
;	short divisor;
;
;	The quotient is returned in the low 16 bits of the result,
;	and the remainder is returned in the high 16 bits.

	public	divrem
divrem	proc
	arg	dividend:dword,divisor:word
	mov	ax,word ptr dividend
	mov	dx,word ptr (dividend+2)
	div	divisor
	ret
divrem	endp
endif	

	public hash_ip
hash_ip	proc
	arg	ipaddr:dword
	lea	bx,Hashtab
	mov	ax,word ptr ipaddr
	xor	ax,word ptr (ipaddr+2)
	xor	al,ah
	xlat
	xor	ah,ah
	ret
hash_ip	endp

	end