WPL -- Wavelet Packet Laboratory Version 1.02 READ.ME General information about the WPL program This program is currently Shareware. Please include this notice in all copies. Any people interested in obtaining the release version should print and fill out the order form in the file ORDER.FRM. Registration entitles the user to technical support and notices of updates to the program. A nominal fee of $50 will be charged for duplications costs. Receipt of payment will register the user. The form should be sent to: Wavelet Packet Laboratory Digital Diagnostic Corp. 26 Rossotto Drive Hamden, CT 06514 Phone: (203)-288-9444 FAX: (203)-287-8765 INTERNET: ddc@cs.yale.edu 1. Introduction The Wavelet Packet Laboratory is a showcase of a new method of analyzing frequencies within signals. The present version has the following limitations: - Floating point ASCII text files can not be loaded - The maximum trace length that the WPT algorithm can handle is 512 - Memory is limited so be careful about the number of images displayed at the same time. Try to keep four to six images the maximum amount loaded. 2. Requirements The minimum requirements of the computer to run this program are: - IBM PC/AT (a 80386 is recommended but not necessary) - 640K of RAM - a hard disk (have plenty of room for files of signals) - EGA or VGA(recommended) color monitor - a mouse is optional but highly recommended - 101 or 102 keyboard (with the F12 key) 3. The Distribution Disk The files included on this disk are: install.bat -- the installation batch file order.frm -- the WPL order form read.me -- this file manual.txt -- the reference manual walkthru.txt -- a tutorial wpl.exe -- the WPL program files wpl.cfg wpl.msg 8x14.apa 8x16.apa _wptfltr.wpl use_ega.bat -- the batch file used to set WPL for EGA monitors use_vga.bat -- the batch file used to set WPL for VGA monitors ega.cfg -- the default wpl.cfg file for EGA vga.cfg -- the default wpl.cfg file for VGA wplcfg.exe -- the WPL configuration program files wplcfg.msg whistle.asc -- a sample ASCII signal file (length = sinxcube.byt -- a sample Signed Byte signal file (length = 512) heart.byt -- another sample Unsigned Byte file (length = 51000) 4. Installation NOTE: The following instructions assume a working knowledge of DOS Also, make sure there is no \WPL in the destination drive A) Boot up your computer and go to the root directory of the drive where the WPL is to be placed. Make sure the drive has at least 720 kilobytes free. Example: the WPL is to be placed on the C drive C:\> B) Insert the distribution disk into the floppy drive and type ":install " Example: the WPL distribution disk is placed into the A drive C:\>A:INSTALL A: C: The \WPL directory is being created ... WPL is being installed ... . . . WPL is now ready to run on a VGA monitor. C:\WPL> C) If your computer has a VGA, then skip this step. Type "USE_EGA" in order to configure WPL to run on EGA monitors Example: WPL is to run with a EGA monitor C:\WPL>USE_EGA D) WPL is ready to run at any time. Simply type WPL when in the \WPL directory. Example: C:\WPL>WPL Before running WPL make sure that there is maximum amount of free memory by removing all TSRs, Terminate and Stay Resident programs. If using the mouse, make sure that the mouse is installed. E) Print the documentation Print the following files: C:\WPL> print manual.txt c:\WPL> print walkthru.txt 5. Error Reporting Please send any error reports, comments, and suggestions to: Wavelet Packet Laboratory Digital Diagnostic Corp. 26 Rossotto Drive Hamden, CT 06514 Phone: (203)-288-9444 FAX: (203)-287-8765 or send by electronic mail to ddc@cs.yale.edu Have your serial number handy. Use System|About to find the serial number.