NAM Programming (Reprogramming) Instructions For 30+ Cellular Telephones <--Part 1--> Presented By: /E/D/I/S/O/N///C/A/R/T/E/R/ Of NETWORK 23 24 HOURS 1200/2400 BAUD (402) 467-2474 ----------------------------------------------------------------------------- PLEASE NOTE: Area specific numbers contained within these programming instructions may not be accurate for your cellular area. ----------------------------------------------------------------------------- Programming Instructions for: DIAMONDTEL MESA90X HANDHELD ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - PRESS FCN 7 ENTER 4 DIGIT SECURITY CODE ENTER NEW 3 DIGIT UNLOCK CODE PRESS CLR PWR up unit Press "END" and hold within 10 seconds of pwr up Enter "5132920" Release END key. 0 SEND DUAL NO XXXXXXXXXX SEND NO1 _ _ _ _ _ SEND SID1 1 SEND LU1 1 SEND EX1 334 SEND IPCH1 07 SEND ACCOLC1 0 SEND PREF1 10 SEND GIM1 0 SEND RI1 1 SEND DTX1 1 SEND AR1 1234 SEND SEC 1 SEND EE 1 SEND C TONE 0 SEND AL 0 SEND BO 1 SEND BEEP TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME TO RESET NAM FROM THE LIMIT OF 3 PROGRAM ATTEMPTS PWR up unit Press "END" and hold within 10 seconds of pwr up TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814" Programming Instructions for: DIAMONDTEL MESA99X HANDHELD ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - PRESS FCN 7 ENTER 4 DIGIT SECURITY CODE ENTER NEW 3 DIGIT UNLOCK CODE PRESS CLR PWR up unit Press "END" and hold within 10 seconds of pwr up Enter "5132920" Release END key. 0 SEND DUAL NO XXXXXXXXXX SEND NO1 _ _ _ _ _ SEND SID1 1 SEND LU1 1 SEND MIN MARK1 334 SEND IPCH1 07 SEND ACCOLC1 10 SEND GIM1 0 SEND RI1 0 SEND DTX1 0 SEND AR1 1234 SEND SEC 1 SEND CONTINUE D.T.M.F. 0 SEND AUTO LOCK 0 SEND BOOSTER TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME Programming Instructions for: GATEWAY CP 900 HANDHELD USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - CURRENT UNLOCK CODE CAN NOT BE SEEN AND MUST BE KNOWN TO CHANGE THE CURRENT UNLOCK CODE. PRESS MENU ENTER 03 ENTER CURRENT 4 DIGIT SECURITY CODE ENTER NEW 4 DIGIT SECURITY CODE PHONE WILL AUTO EXIT TO READY ACTION TO STORE DISPLAY PRESS MENU 99 ENTR SCRTY CODE(FCTRY PRST IS 9999) PROGRAM NAM _ _ _ _ _ SEND SID XXXXXXXXXX SEND PHONE NUMBER 0334 SEND IPC 07 SEND ACCOL 10 SEND GIM 1 SEND MOBILE I.D. NUMBER 1 SEND LOCAL USE MARK 2 SEND SYSTEM SELECT (B) UPON PRESSING SEND THE PHONE WILL CYCLE TO WAIT AND THEN RETURN TO THE READY MODE. TO DISPLAY THE NEW PHONE NUMBER: PRESS RCL 00 Programming Instructions for: GENERAL ELECTRIC MINI II ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - PRESS FCN 7 ENTER 4 DIGIT SECURITY CODE ENTER NEW 3 DIGIT UNLOCK CODE PRESS CLR PWR up unit Press and hold END key within 10 seconds of pwr up Enter "6282905" Release END key 0 Press SEND DUAL NO XXXXXXXXXX Press SEND NO1 _ _ _ _ _ Press SEND SID1 1 Press SEND LU1 1 Press SEND EX1 0334 Press SEND IPCH1 07 Press SEND ACCOLC1 0 Press SEND PREF1 10 Press SEND GIM1 0 Press SEND RI1 1 Press SEND DTX1 1 Press SEND AR1 1234 Press SEND SEC 1 Press SEND EE 1 Press SEND C DTMF 0 Press SEND AL 0 Press SEND BEEP 0 Press SEND BO TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME Programming Instructions for: GENERAL ELECTRIC MINI ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE FOLLOW THE INSTRUCTIONS THAT FOLLOW PWR up unit Press and hold CL key within 10 seconds of pwr up 0Enter "7591122" Release CL key XXXXXXXXXX PRESS SEND MIN 123 PRESS SEND UNLOCK _ _ _ _ _ PRESS SEND SID 1 PRESS SEND LU 1 PRESS SEND MIN MARK 334 PRESS SEND IPCH 07 PRESS SEND ACCOLC 0 PRESS SEND PS 10 PRESS SEND GIM 1 PRESS SEND EE 0 PRESS SEND BOOSTER 1 PRESS SEND AR TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME Programming Instructions for: MITSUBISHI 800 ACTION TO STORE DISPLAY PWR up unit Press and Hold STO within 10 Seconds of pwr up Enter "5474432" Release STO 0 Press SEND dUAL XXXXXXXXXX Press SEND NO1 _ _ _ _ _ Press SEND SId1 1 Press SEND LU1 0 Press SEND MIN Mark 0334 Press SEND IPCH 07 Press SEND ACCOLC 0 Press SEND PS1 10 Press SEND GI1 1234 Press SEND SECUrity 1 Press SEND EE 0 Press SEND dt 1 Press SEND HF 0 Press SEND InHIbit 1 Press SEND C tOnE 0 Press SEND SyS A/B 0 Press SEND dUAL HS 0 Press SEND InHibit Ld TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME Programming Instructions for: MITSUBISHI 900 ACTION TO STORE DISPLAY PWR up unit Press and Hold END key within 10 seconds of pwr up Enter "6972814" Release END key 0 Press SEND DUAL NO XXXXXXXXXX Press SEND NO1 _ _ _ _ _ Press SEND SID1 1 Press SEND LU1 0 Press SEND EX1 0334 Press SEND IPCH1 07 Press SEND ACCOLC1 0 Press SEND PREF1 10 Press SEND GIM1 0 Press SEND RI1 1 Press SEND DTX1 1 Press SEND AR1 1234 Press SEND SEC 1 Press SEND EE 1 Press SEND C DTMF 0 Press SEND AL 0 Press SEND BO 1 Press SEND BEEP TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME TO ENTER TEST MODE HOLD END ON PWR UP-CODE 0944635 Programming Instructions for: MOTOROLA 8000H ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - THIS FUNCTION IS PROVIDED IN STEP 9 OF THE PROGRAMMING MODE PWR up unit Enter STORE #123456123456 RCL If the phone is fresh from factory then Enter STORE #000000000000 RCL If the phone is used or already programmed then Enter STORE #123456123456 RCL DISPLAY WILL SHOW 01 PRESS * _ _ _ _ _ * 02 (SID) XXX * 03 (Area Code) XXX XXXX * 04 (Phone #) 14 * 05 07 * 06 00 * 07 123456 * 08 123 * 09 334 * 10 010100 * 11 000 * PRESS * TO REVIEW ENTRIES TO BURN NAM: PRESS SEND WHILE 01,02,03, ETC. IS DISPLAYED SET TO SCAN B MODE BY : RCL * : PRESS * UNTIL SCAN B MODE SHOWS then: press store Programming Instructions for: MOTOROLA ULTRA CLASSIC HANDHELD ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - THE UNLOCK CODE IS PROGRAMMED IN STEP 8 OF THE PROGRAMMING MODE FOR NEW PHONE: Press FCN, 0 + Security code entered twice (Factory preset is 000000), RCL The message 01 will appear in the display to confirm programming mode. Press * 01 Press * 1) _ _ _ _ _ Press * 02 Press * 2) XXX Press * 03 Press * 3) XXX XXXX Press * 04 Press * 4) 14 Press * 05 Press * 5) 07 Press * 06 Press * 6) 10 Press * 07 Press * 7) 123456 Press * 08 Press * 8) 123 Press * 09 Press * 9) 0334 Press * 10 Press * 10) 010101 Press * 11 Press * 11) 101 Press * 12 Press * Review entries by pressing "*" repeatedly. Press SEND to program phone. Programming Instructions for: NEC P300 ACTION TO STORE DISPLAY THESE INSTRUCTIONS FOR SERIAL NUMBERS AFTER 135-839601 Insert NAM Programming Adapter (NECAM #41-2019) into plug connector on P300 phone bottom. PWR On RCL # 0 1 to enter test mode. Phone will display shaded blocks. RCL # 7 6 to select NAM. Phone will show 76- Press 0 # to program NAM 1. (NAM 1=0,NAM 2=1,NAM 3=2,NAM 4=3) RCL # 7 1 to enter programming mode. XXXXXXXXXX PRESS # MIN 1234 PRESS # LOCK CODE _ _ _ _ _ PRESS # SID 10 PRESS # GROUP I.D. 0334 PRESS # INITIAL PAGING CH 0 PRESS # SYSTEM SELECT (1=A) 07 PRESS # ACCOLC 1 PRESS # MIN MARK 1 1 PRESS # LOCAL USE 911 PRESS # EMERGENCY NO. Press Clr (and hold) to exit programming and return to TEST MODE. Press RCL # 0 2 to burn and exit to standby. THESE INSTRUCTIONS FOR SERIAL NUMBERS PRIOR TO 135-839601 Insert NAM Programming Cable (41-2019) PWR on RCL # 7 6 to enter TEST MODE Press 0 # to select NAM. RCL # 7 1 You are now in Programming Mode. Enter NAM info as above. Press and hold CLR to exit. Pwr down. Programming Instructions for: NEC P9100 ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE FOLLOW THE INSTRUCTIONS THAT FOLLOW Make sure NAM battery is fully charged before attempting programming Switch power on Press RCL #01 display will then show shaded blocks For a USED phone - to clear nam and accumulated call timer Press RCL #39 To program NAM1 Press RCL #760# To enter programming mode Press RCL #71 XXXXXXXXXX Press # MIN 1234 Press # Lock Code _ _ _ _ _ Press # SYS. I.D. 10 Press # G.I. Mark 0334 EMPTS FOLLOW THE BLOCK OF INSTRUCTIONS AT TOP USING "8291112" W/CLR TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814" Programming Instructions for: FUJITSU MOBILE PHONE ACTION TO STORE DISPLAY PWR up unit Unit must be locked to program. To lock press F+LOCK PWR down unit. PWR up unit. Within 10 seconds press #626#7764726 (#NAM#PROGRAM) A continuous tone will be heard for 7 seconds. PRESS AND HOLD THE * KEY WHILE THE TONE SOUNDS, DO NOT LET GO! The tone will change to an intermittent tone, then it will stop. Release the * key. CONGRATULATIONS!!! YOU ARE NOW IN PROGRAMMING MODE! _ _ _ _ _ PRESS STOR 1 SIDH 1 PRESS STOR 2 LOCAL 1 PRESS STOR 3 MIN MARK XXXXXXXXXX PRESS STOR 4 MIN 10 PRESS STOR 5 STATION 0334 PRESS STOR 6 IPCH 07 PRESS STOR 7 ACCOLC 0 PRESS STOR 8 PS 10 PRESS STOR 9 GIM 1234 PRESS STOR 10 LOCK 1 PRESS STOR 11 CALL TIME 2 PRESS STOR 12 AUTO LOCK 1 PRESS STOR 13 CALL REST PRESS STOR TO REVIEW ENTRIES. WHEN AT MODE #1 PRESS SEND TO BURN NAM AND RETURN TO NORMAL OPERATION. IF PROGRAMMING WAS DONE INCORRECTLY A SHORT HIGH TONE WILL BE HEARD, YOU MUST THEN REPEAT DATA ENTRY. YOU MUST PRESS STOR AFTER EACH ENTRY FOR THE CHECKSUM FUNCTION TO BE FULFILLED. Programming Instructions for: GENERAL ELECTRIC CARFONE XR3000 ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - THE UNLOCK CODE IS PROGRAMMED IN STEP 2 OF THE PROGRAMMING MODE PWR up unit Press "CL" and hold within 10 seconds of pwr up Enter "923885" Serial # will display Press Send key to advance to first entry XXXXXXXXXX Press SEND MIN 123 Press SEND UNLOCK _ _ _ _ _ Press SEND SID 1 Press SEND LU 1 Press SEND MIN MARK 334 Press SEND IPCH 07 Press SEND ACCOLC 0 Press SEND PS 10 Press SEND GIM 0 Press SEND AUX 1 Press SEND HANDS PRESS SEND TO REVIEW ENTRIES. NOTE: AREA CODE (402) WILL DISPLAY FOR MIN THEN AUTO SWITCH TO REST OF NUMBER ON DISPLAY - BE PATIENT PRESS "E" KEY TO COMPLETE PROGRAMMING OF THE XR 3000 AT THIS TIME Programming Instructions for: GOLDSTAR SERIES 5000 MOBILE ACTION TO STORE DISPLAY PWR up Unit Press FCN 4 to see the selected NAM. Press * to advance. Select NAM1. Press FCN, 9, 9, * "Enter Code" will be displayed. Enter 1234567890 XXXXXXXXXX PRESS MEM Enter MIN _ _ _ _ _ PRESS MEM Enter System ID 0334 PRESS MEM Enter IPCH 07 (ACCOLC) PRESS MEM Enter OVLD Class 1234 PRESS MEM LOCK CODE 123456 PRESS MEM SECURITY CODE 1234 PRESS MEM ALARM DISARM CODE 0 PRESS MEM PREFFERED SYSTEM 0 PRESS MEM STATION CLASS MARK 1 PRESS MEM HANDS FREE MARK (ON) 1 PRESS MEM LOCAL USE MARK (ON) 1 PRESS MEM MIN MARK (ON) 0 PRESS MEM HORN ALERT (OFF) 0 PRESS MEM OPT. SPEAKER (OFF) TO SAVE TO NAM NOW PRESS MEM TO REVIEW ENTRIES USE THE VOLUME UP OR DOWN KEYS Programming Instructions for: MITSUBISHI 555,560,600 ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - TO PROGRAM THIS FUNCTION YOU MUST BE OUT OF THE PROGRAMMING MODE ENTER FCN 6 AND THEN ENTER THE NEW 3 DIGIT UNLOCK CODE PRESS CLR. To program from keypad remove and discard Nam Pad PWR up unit Press and Hold STO key within 10 seconds of pwr up Enter "5474432" Release STO key XXXXXXXXXX Press SEND MIN 123 Press SEND SECURITY CODE _ _ _ _ _ Press SEND SID 1 Press SEND LU 1 Press SEND MIN MARK 334 Press SEND IPCH1 07 Press SEND ACCOLC1 0 Press SEND PS1 10 Press SEND GIM 1 Press SEND EE 1 Press SEND HANDS FREE 0 Press SEND ROAM INHIBIT 0 Press SEND A/B SELECT 00 Press SEND f3-f0 DUAL HEAD 00 Press SEND f7-f4 LD INH TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME Installing the LOCK CODE To program the customer's lock code, the phone must be out ot the programming mode. To program, enter FCN, 6,3-digit security code, the a 3-digit lock code. Press CLR. Programming Instructions for: NEC M3700 SERIES MOBILE ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE FOLLOW THE INSTRUCTIONS THAT FOLLOW A NAM PROGRAMMER ADAPTOR (NECAM #41-2012) IS REQUIRED PWR UP TO ENTER TEST MODE: RCL, #,0,1. WILL CYCLE TO SHADED TO CLEAR MEMORY: RCL # 3 9 select nam RCL # 7 6 0 # nam 1 RCL # 7 6 1 # nam 2 TO ENTER PROGRAMMING MODE: RCL #71 XXX XXX XXXX PRESS # Telephone No. (MIN) 1234 PRESS # Lock Code _ _ _ _ _ PRESS # Home Area (SYS I.D.) 10 PRESS # G-NO (Group I.D.) 0334 PRESS # First Paging Channel 0 for wireline PRESS # System Select 07 PRESS # ACCOLC 1 PRESS # ACCESS 1 PRESS # Local Use To exit PROGRAMMING MODE PRESS CLR and hold TEST MODE will show to exit TEST MODE RCL #02 IF MEM WAS CLEARED VIA RCL #39, PHONE WILL AUTOMATICALLY ENTER FULL-LOCK AFTER EXITING THE TEST MODE. TO UNLOCK PRESS FCN # 1234. Programming Instructions for: NOKIA LX-11 ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - PRESS SEL,5 THEN ENTER 5 DIGIT SECURITY CODE PRESS SEL TO RECEIVE DISPLAY OF CURRENT UNLOCK CODE PRESS 5 NOW TO CLEAR ALL CALL TIMERS ENTER THE NEW UNLOCK CODE PRESS SEL TO ACCEPT PWR up unit Enter *3001#12345 Then - SEL 9 END IdEnt IF InFO should appear on display Pressing END will move you through the parameters Pressing SND will toggle between choices available _ _ _ _ _ Press END HO-Id (SID) 1 Press END ACCESS 1 Press END LOCL OPt XXXXXXXXXX Press END Phonxx 08 Press END St CLASS 334 Press END PAging Ch 07 Press END O-LOAd CLASS B Press END PrEF SyS 10 Press END grOUP Id 12345 Press END SECUrIty -------- (Can't be changed) Press END 1 dAtE 00/00/90 (INSTALLATION DATE) Press END 2 dAtE TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END" TO STORE LAST PARAMETER THEN POWER DOWN WHEN THE "END" KEY IS PRESSED FOLLOWING THE LAST PARAMETER, THE TEXT Prog donE WILL APPEAR ON DISPLAY Programming Instructions for: NOKIA M-10 ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - THIS FUNCTION IS PROVIDED BY THE SECURITY CODE PROGRAMMED AT THE TIME OF PROGRAMMING PWR up unit Enter *17*3001*1234* HO-Id must appear on display Press SEL to view current value Display will be one step behind TO STORE instructions _ _ _ _ _ Press SEL ACCESS (SID) 1 Press SEL LOCAL 1 Press SEL PhonE n XXXXXXXXXX Press SEL CLASS 08 Press SEL PAGE ch 334 Press SEL O-LOAd 07 Press SEL GrouP 10 Press SEL SEC 1234 Press SEL AUTO EXIT PROGRAM MODE TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END" WHEN THE SEL KEY IS PRESSED FOLLOWING THE LAST PARAMETER VALUE, THE PHONE WILL AUTOMATICALLY EXIT THE NAM PROGRAMMING MODE AND RETURN TO NORMAL OPERATION Programming Instructions for: NOVATEL 8305 TRANSPORTABLE CA08 SOFTWARE VERSION USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - IF EQUIPMENT IS PROVIDED WITH A MENU KEY THEN ENTER THE MENU PORTION OF THE PHONE AND DISPLAY AND IF NECESSARY REPROGRAM THE UNLOCK CODE FROM THERE. IF PHONE DOES NOT HAVE A MENU KEY THEN THERE CAN BE NO PROGRAMMING OF THE UNLOCK CODE... THE SECURITY CODE WILL BE ALL THAT IS PROVIDED Lock Phone by pressing FCN 1 Enter Programming Mode by pressing #259 Screen will display the software revision number Press Volume Up Screen will display Phone's E.S.N. Press Volume Up Screen will display INIT REP USE SND Press SEND to erase any numbers stored in the phones memory Press Volume Up _ _ _ _ _ Send Vol. Up SIDH system I.D. XXX XXX XXXX Send Vol. Up MIN mobile I.D. Must be changed when done Send Vol. Up LOCK CODE 1 programming - BY CUSTOMER Must be changed when done Send Vol. Up LOCK CODE 2 programming - BY CUSTOMER SET Vol. Up Option EX extnd adrss 334 press send to change Vol. Up IPCH initial pge 07 Send Vol. Up ACCOLC overload 10 Send Vol. Up GIM group i.d. 333 Vol. Up IDCCA initl a 334 Vol. Up IDCCB initl b 1 Vol. Up REG TBL SIZE Volume up through the four invalid System I.D. addresses SET Vol. Up OPTION LU local use B press send to change Vol. Up OPTION PS (prefered sys) CLR Vol. Up OPTION IRI rm inhbt CLR Vol. Up OPTION SSD SET Vol. Up OPTION QRC qck rcall SET Vol. Up OPTION QST qck store SET Vol. Up OPTION WUT wake tone SET Vol. Up OPTION EE use dtmf SET Vol. Up OPTION FD use dtmf SET Vol. Up OPTION MFD ext dtmf SET Vol. Up OPTION 32D dgt dial CLR Vol. Up OPTION MLH timer CLR Vol. Up OPTION LHM timer CLR Vol. Up OPTION CRU timer dsp CLR Vol. Up OPTION NLM timer SET for on CLR for off Vol. Up OPTION HA hrn alert CLR Vol. Up OPTION ONL diagnostc END to exit or VOLUME UP to review entries. Programming Instructions for: OKI CDL400 ACTION TO STORE DISPLAY To Enter Programming mode: Press IN SEQUENCE: END RCL FUNC CLR SND Screen shows Entr id Enter 08693427 XXX XXX XXXX PRESS # PRESS * PHon _ _ _ _ _ PRESS # PRESS * S id no 0334 PRESS # PRESS * iPCH 07 PRESS # PRESS * ACC oLC 123 PRESS # PRESS * LoC Cod 10 PRESS # PRESS * G id 0000 PRESS # PRESS * Stn CLS 0111 PRESS # PRESS * HORN ALERT, HANDS FREE, LOCAL USE, MIN. MARK. PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE. __________________________________________________________________________ TO REPROGRAM TELEPHON NUMBER AND SYSTEM I.D. # - PRESS IN SEQUENCE THE FOLLOWING KEYSTROKES: FUNC 90 * 123 (SECURITY CODE) PHon WILL DISPLAY ENTER NEW PHONE NUMBER XXX XXX XXXX PRESS # PRESS * PHon _ _ _ _ _ PRESS # PRESS * S id no PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE. ___________________________________________________________________________ To Re-Initialize Nam Memory for Handset Programmable Models - Func 99* Enter Last 8 digits of S.N. Press * Programming Instructions for: PANASONIC EB362 Charged Battery and Nam Adaptor(Grey Cord w/25pin Connector)are needed. ACTION TO STORE DISPLAY USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE - THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE *0000# to enter program mode *1 Press SND 50 Press SND NAM 1 MODE _ _ _ _ _ Press STO 01 SIDH XXXXXXXXXX Press STO 02 OWNDL 1 2 3 Press STO 03 LOCK 0 0 0 0 0 0 0 0 0 0 0 0 (12) Press STO 04 SPDL