--------------------
Chrome Box
--------------------

    Emergency vehicles in many cities are now using devices called OptoComs.
  OptoComs are a system of sensors on traffic lights that detect a pattern
  of flashes from vehicle-mounted strobe lights.

    This flash pattern varies from city to city depending on the manufacturer
  of the equipment used.  Often the sensors are installed only at major
  intersections.  Nevertheless, the Chrome Box, which simulates these strobe
  patterns can often be used to give your car the same priority as an
  ambulance, paramedic van, firetruck or police car.

    Because of the varying patterns on different systems this phile will
  outline a general procedure for making the Chrome Box.

  Decoding Flash Patterns:

   First, you need to observe an emergency vehicle in action.  You can wait
  until you encounter one by chance, running out to see when you hear a siren,
  or when you pull over in your car to let one pass by. You might wait near a
  fire station for the next emergency to occur.  Or, if you are very
  impatient, you can summon one by calling in a false alarm (not recommended
  in areas with limited services - that could divert attention from a real
  emergency).  If the OptoComs in your area are the kind with a pattern of
  single flashes at a steady rhythm, you have merely to buy a strobe light at
  Radio Shack & adjust the flash rate until you can induce a traffic light to
  change.

   If the flash pattern is more complex, you can videotape the emergency
  vehicle & then play back the tape in single-frame mode, counting the number
  of frames between each flash. Each video frame is 1/30 of a second, using
  this you can calculate the time between flashes in the pattern.  Another way
  is to count the number of flashes (or flash-groups) in one minute and use
  that to compute the rate. Counting video frames will give you a good idea of
  the spacing of the flashes in a complex pattern.  For really accurate
  information, call the fire station & ask them, or write to the manufacturer
  for a service manual, which will include a schematic diagram that you can
  use to build one. A good cover story for this is that you are a consultant &
  one of your clients asked you to evaluate Optocom systems, or you could pose
  as a free-lance journalist writing an article.

  Modifying the Strobe Light:

   You may not have to modify the strobe at all. But if you need a faster
  flash rate than your strobe allows, open it up & find the large capacitor
  inside. Capacitors are marked in microfarads, abbreviated as mf,mfd or ufd.
  By replacing the capacitor with one of the same voltage-rating (usually
  250 volts or more) and a SMALLER value in microfarads, you can increase the
  flash rate. Halving the microfarads doubles the rate.
   The other component that can be changed is the potentiometer (the speed
  control device with the knob on it). Using a smaller value (measured in
  ohms or Kilohms, abbrevaited with the greek letter 'omega' or the letter K)
  will speed up the strobe. There may also be a resistor (small cylinder with
  several colored stripes on it, and wires coming out of each end). Replacing
  this resistor with one of smaller value will also speed up the strobe.

   To generate a complex pattern, you will either have to design and build a
  triggering circuit using IC chips, or rig up a mechanical device with a
  multiple-contact rotary switch and a motor.  It HAS been done.

   To modify the strobe for mobile operation the simplest thing is to get a
  110-volt inverter that will run off of a car battery by plugging into the
  cigarette lighter & run the strobe from that.  Or, you can figure out (or find
  in a hobby electronics magazine) a strobe circuit that will run from batteries
.
  Battery-powered strobes may also be availble, either assembled or as kits.

  Stealth Technology:

   Most light sensors and photocells are more sensitive in the infrared area of
  the light spectrum. Infrared (IR) is invisible to the human eye. Putting an
  infrared filter over the strobe light may allow the Chrome Box to operate in
  traffic undetected by police or other observers. IR filters can be obtained
  from military surplus sniperscope illuminators, or from optical supply
  houses like Dow-Corning or Edmunds Scientific Co.

  Using the Chrome Box:

   Mounted on your car, the Chrome Box can guarantee you green lights at major
  intersections in cities that have OptoComs. Handheld Chrome Boxes may be
  used to create gridlock by interfering with the normal flow of traffic.  If
  you have access to a window overlooking a traffic light, you can play pranks
  by switching the signals at inappropriate moments, or you can plug the
  strobe into an exposed outlet at a laundromat or gas station.

  Some Decoded Patterns:

  Torrance, California
      Standard large Radio Shack strobe lights are used. Moderately fast rate.
      *  *  *  *  *  *  *  *

  Manhattan Beach,CA
     Flash-pairs in a 4:1 ratio, at a rate of 2 flash-pairs per second.
     * *       * *       * *       * *
     <------ 1 sec ----->

--------------------