1,* * *     C O N F I G U R A T I O N   M A I N   M E N U     * * *;
2,1) Select a Video Graphics Display;
3,2) Select a Pointing Device;
4,3) Select a Plotter;
5,4) Set Screen Ratio;
6,5) Other Options ;
7,ESC) Exit to DOS ;
8,7) Locate a DIGITIZER MENU on the Digitizer;
9,Enter a selection number. >>> ; 
10,***   C O N F I G U R A T I O N   S U B - M E N U   ***;
11,1) Set Mouse and Digitizer Options;
12,2) Set Default Paths for Files;
13,3) Set Color Selections;
14,4) Set Drawing Units of Measure ;
15,5) Set Snap & Trim Options;
16,6) Set AutoDimensioning Options;
17,8) Other Options;
18,ESC) Return to Previous Menu;
19,Enter a selection number. >>> ;
20,*****  SELECT A VIDEO GRAPHICS DISPLAY  *****;
21,Unable to find the Video Drivers !!;
22,Please enter the Disk Drive (example, B:) ;
23,AND/OR the Directory (example, \config\) ;
24,where the CONFIGURATION Files are located >> ;
25,*****  SELECT A VIDEO GRAPHICS DISPLAY  *****;
26,Video Drivers Are Available For The Following Displays: ;
27, ;
28,Enter a selection, then hit the RETURN key >>> ;
29,*****  SELECT A POINTING DEVICE  *****;
30,Unable to find the Pointing Device Drivers !!;
31,Please enter the Disk Drive (example, B:) ;
32,AND/OR the Directory (example, \config\) ;
33,where the CONFIGURATION Files are located >> ;
34,*****  SELECT A POINTING DEVICE  *****;
35, The following Pointing Device Drivers Are Available: ;
36, ;
37, ;
38,Enter a selection number, or hit ENTER for next page >>> ;
39,*****  SELECT A POINTING DEVICE  *****;
40,The following Sizes Are Available for this Digitizer:;
41, ;
42, ;
43,Enter the selection, then hit the RETURN key >>> ;
44,*****  SELECT A POINTING DEVICE  *****;
45,Which ADDRESS Will The Pointing Device Use ? ;
46,(1) 238 ;
47,(2) 338 ;
48,(3) 3F8 ;
49,(4) 2F8 ;
50,ENTER SELECTION  >> ;
51,***** SET BUS MOUSE INTERRUPT LEVEL *****;
52,Which Interrupt level is the Bus Mouse jumpered for ?;
53,NOTES: ;
54,PCs & XTs are usually set to Interrupt Level 2;
55,ATs are usually set to Interrupt Level 5;
56,ENTER SELECTION (2 - 5, 7, 10 - 12, 15)) >> ;
57,*****  SELECT A POINTING DEVICE  *****;
58,Which I/O Port Will The Pointing Device Use ? ;
59,(1) COM1 ;
60,(2) COM2 ;
61,ENTER SELECTION  >> ;
62,***** SET BUS MOUSE INTERRUPT LEVEL *****;
63,Which Interrupt level is the Bus Mouse jumpered for ?;
64,NOTES: ;
65,PCs & XTs are usually set to Interrupt Level 2;
66,ATs are usually set to Interrupt Level 5;
67,ENTER SELECTION (2 - 5) >> ;
68,*****  SELECT A PLOTTER  *****;
69,Unable to find the Plotter Drivers !!;
70,Please enter the Disk Drive (example, B:) ;
71,AND/OR the Directory (example, \config\) ;
72,where the CONFIGURATION Files are located >> ;
73,*****  SELECT A PLOTTER  *****;
74, The following Plotter Drivers Are Available: ;
75, ;
76, ;
77,Enter a selection number, or hit ENTER for next page >>> ;
78,*****  SELECT A PLOTTER  *****;
79,Which I/O Port Will The Plotter Use ? ;
80,(1) COM1 ;
81,(2) COM2 ;
82,(3) LPT1  ;
83,ENTER SELECTION (1 - 5) >> ;
84, * * *     S E T   S C R E E N   R A T I O    * * *;
85,The Video Display Size parameters are used to set the Video;
86,Display Screen Ratio so that round objects appear round and;
87,square objects appear square on the GRAPHICS Video Display.;
88,The Height and Width parameters should be set to the NEAREST;
89,10th of an Inch OR NEAREST Millimeter, USING the outside dimensions;
90,of the maximum visual display of the GRAPHICS video display screen.;
91,If the screen that you are viewing this on is your GRAPHICS screen;
92,then use the RED display box drawn on this screen for your dimensions.;
93,1) Video Display Height  ;
94,2) Video Display Width   ;
95,ESC) Return to Previous Menu;
96,Enter a selection number. >>> ;
97,* * *    C U R R E N T   C O N F I G U R A T I O N    * * *;
98, CANNOT CONFIGURE GENERIC CADD BECAUSE: ;
99, NOT CONFIGURED FOR A VIDEO BOARD !! ;
100,NOT CONFIGURED FOR A PLOTTER !! ;
101,NOT CONFIGURED FOR A DIGITIZER !! ;
102,VIDEO GRAPHICS DISPLAY: ;
103,Graphics and Control Text on First Screen;
104,Graphics and Control Text on Second Screen;
105,Graphics on Second Screen, Control Text on First Screen;
106,PLOTTER: ;
107,On COM Port ;
108,Configured: ;
109,On Port LPT;
110,POINTER: ;
111,Tablet Size Of: ;
112,On Address ;
113,On Interupt Level ;
114,On COM Port ;
115,Configured: ;
116,On Interrupt Level ;
117,DRAWING UNITS: ;
118,METERS;
119,CENTIMETERS;
120,MILLIMETERS;                              
121,FEET;
122,FEET/INCHES;
123,INCHES;
124,DO YOU WISH TO KEEP THE CHANGES ? (Y, N) >> ;
125,CONFIGURING THE GENERIC CADD WORK DISK ....     ;
126, DO YOU WISH TO ABORT THIS SESSION ? (Y, N) >> ;
127,* * *   M O U S E   A N D   D I G I T I Z E R   O P T I O N S   * * *;
128,1) Set the Pointer Buttons  ;
129,2) Locate the Digitizer Menu on the Digitizer   ;
130,7) Configure Serial I/O Ports   ;
131,3) Video Menu Display is ;
132,ON ;
133,OFF ;
134,4) Digitizer Menu is ;
135,5) Set the Function Keys ;
136,ESC) Return to Previous Menu;
137,Enter a selection number. >>> ;
138,* * *    S E T   D E F A U L T   P A T H S   * * *;
139,Current Default Paths are set as follows:;
140,1) Path for Drawing Files: ;
141,2) Path for Component Files: ;
142,3) Path for Text Font Files: ;
143,ESC) Return to Previous Menu;
144,Please select what path to change.;
145,Enter a selection number. >>> ;
146,Enter a new Path > ;
147,Ex: same drive different dir.:->  \DWG\;
148,Ex: different drive and dir. :->  C:\DWG\;
149,Ex: different drive.         :->  A:;
150,Ex: sub-directory.           :->  DWG\ ;
151, ;
152,*  *  *    S E L E C T   C O L O R S    *  *  *;
153,1) Select Display Cursor Color;
154,2) Select Display Text Color;
155,3) Select Drawing Line Color;
156,4) Select Drawing Text Color;
157,5) Select Drawing FILL Color;
158,6) Select Drawing HATCH Color;
159,7) Select Drawing DIMENSION Color;
160,ESC) Return to Previous Menu;
161,Enter a selection number. >>> ;
162,***    D R A W I N G   U N I T   P A R A M E T E R S   ***;
163,1) Drawing Units are ;
164,METERS       ;  
165,CENTIMETERS  ;   
166,MILLIMETERS  ;
167,FEET         ;
168,FEET/INCHES  ;
169,INCHES       ;
170,2) Fraction Display is ;
171,ON ;
172,OFF ;
173,3) Fraction Value is ;
174,4) Decimal Value is ;
175,5) Angle Display is in ;
176,MINUTES;
177,DEGREES;
178,6) Absolute Coordinate Display is ;
179,ON ;
180,OFF;
181,7) Delta Coordinate Display is ;
182,8) Polar Coordinate Display is ;
183,9) Set Drawing Size (limits) ;
184,ESC) Return to Previous Menu ;
185,Enter a Selection number, then hit the RETURN key  >>> ;
186,* * *   S N A P   A N D   T R I M   O P T I O N S   * * *;
187,1) Grid Size is ;
188,2) Grid Display is ;
189,ON ;
190,OFF;
191,3) Grid Snap is ;
192,4) Search Tolerance is ;
193,5) Fillet Radius is ;
194,6) Chamfer Distance 1 is ;
195,7) Chamfer Distance 2 is ;
196,8) Double Line OFFSET 1 is ;
197,9) Double Line OFFSET 2 is ;
198,10) Solid Line is ;
199,11) Auto_Fillet is ;
200,12) Component Snap is ;
201,ESC) Return to Previous Menu ;
202,Enter a selection number , then hit the RETURN key >>> ;
203,* * *   A U T O   D I M E N S I O N I N G   P A R A M E T E R S   * * *;
204,1) Dimension MODE is ;
205,SINGLE     ;
206,PARTITIONED ;
207,CUMULATIVE ;
208,2) Dimension Direction is ;
209,ALIGNED    ;
210,HORIZONTAL ;
211,VERTICAL   ;
212,3) Dimension Layer is ;
213,4) Letter Direction is ;
214,ALIGNED    ;
215,HORIZONTAL ;
216,5) Letter Placement is ;
217,INLINE  ;
218,OVERLINE;
219,6) Letter Size is ;
220,7) Letter Font is ;
221,8) Arrow Type is a ;
222,15 Degree Head;
223,30 Degree Head;
224,45 Degree Head;
225,60 Degree Head;
226,Circle Head ;
227,9) Arrow Mode is ;
228,CLOSED  ;
229,OPEN    ;
230,10) Proximity Fixed is ;
231,ON ;
232,OFF;
233,11) Extension Line Offset is ;
234,**************************** ;
235,12) Extension Line Length ABOVE:;
236, BELOW:;
237,13) Extension Stretch is ;
238,ON ;
239,OFF;
240,14) Shoulder Length is ;
241,ESC) Return to Previous Menu ;
242,Enter a selection number, then hit the RETURN key >>> ;
243,1 = SINGLE, 2 = PARTITIONED, 3 = CUMULATIVE ;
244,DIMENSION MODE ;
245,1 = ALIGNED, 2 = HORIZONTAL, 3 = VERTICAL ;
246,DIMENSION DIRECTION ;
247,DIMENSION LAYER     ;
248,LETTER DIRECTION    ;
249,LETTER PLACEMENT    ;
250,LETTER HEIGHT ;
251,SELECT DIMENSION FONT ;
252,1 = 15 DEG, 2 = 30 DEG, 3 = 45 DEG, 4 = 60 DEG, 5 = CIRCLE, 6 = SLASH;
253,ARROW HEAD TYPE ;
254,EXTENSION OFFSET ;
255,EXTENSION LINE LENGTH ABOVE ;
256,EXTENSION LINE LENGTH BELOW ;
257,LEADER SHOULDER SIZE ;
258,* * *     M I S C E L L A N E O U S    O P T I O N S    M E N U    * * *;
259,1) Construction Points Display is ;
260,ON ;
261,OFF;
262,2) Reference Points Display is ;
263,3) Video Menu Display is ;
264,4) Status Lines Display is ;
265,5) Rubber Banding is ;
266,ESC) Return to Previous Menu;
267,Enter a selection number. >>> ;
268,GRID SIZE  ;
269,TOLERANCE  ;
270,FILLET RADIUS ;
271,CHAMFER DISTANCE 1  ;
272,CHAMFER DISTANCE 2  ;
273,Double Line OFFSET 1 ;
274,Double Line OFFSET 2 ;
275,1) Set New Fraction Value ;
276,2) Return to Units Menu;
277,(1 = mm , 2 = cm , 3 = meters , 4 = feet , 5 = ft/in , 6 = inches );
278,ENTER THE FONT NAME > ;
279,FILE ;
280, NOT FOUND !! ;
281,IS THIS A NEW FONT ? (Y,N) > ;
282,SELECTED FONT IS: ;
283,FONT ;
284,IS SELECTED ;
285,* * *     S E T   D R A W I N G   S I Z E    * * *;
286,The Drawing Size parameters are used to assist the operator;
287,in viewing and in drawing differently sized objects. ;
288,The Height and Width Limits should be set to the MAXIMUM real world;
289,dimensions of the object to be drawn, (i.e., 600" X 800") NOT the;
290,size of the drawing paper !!;
291,1) Drawing Height  ;
292,2) Drawing Width  ;
293,ESC) Return to Previous Menu;
294,Enter a selection number. >>> ;
295,HEIGHT ;
296,WIDTH ;
297,* * *    S E R I A L   P O R T   C O N F I G U R A T I O N    * * *;
298, The Configuration for the Device Serial Ports are: ;
299,POINTER, ON PORT ;
300,PLOTTER, ON PORT ;
301,1)  Change Configuration of POINTER Serial Port.;
302,2)  Change Configuration of PLOTTER Serial Port.;
303,ESC)  Return to Previous Menu.;
304, Enter a selection number. >>> ; 
305, Configuration for ;
306,POINTER Serial Port;
307,PLOTTER Serial Port;
308, Baud Rates Available:;
309,1)   300;
310,2)   600;
311,3)  1200;
312,4)  2400;
313,5)  4800;
314,6)  9600;
315, Enter a selection number. >>> ; 
316, Configuration for ;
317, Parity Available:;
318,1)   Odd;
319,2)  None;
320,3)  Even;
321, Enter a selection number. >>> ; 
322, Configuration for ;
323, Stopbits Available: ;
324,1)  One bit;
325,2)  Two bits;
326, Enter a selection number. >>> ; 
327, Configuration for ;
328, Wordlengths Available:;
329,1)  Seven bits;
330,2)  Eight bits;
331, Enter a selection number. >>> ; 
332,The Configuration that you have set for the;
333,POINTER Serial Port is: ;
334,PLOTTER Serial Port is: ;
335,Is This The Correct Configuration ? (Y,N)  >> ;
336,* * *     S E T   F U N C T I O N   K E Y S    * * *;
337,ESC) Return to Previous Menu;
338,Enter a selection number, then hit the RETURN key >>> ;
339,ENTER A NEW TWO LETTER COMMAND FOR FUNCTION KEY # ;
340,* * *      S E T   D I G I T I Z E R   B U T T O N S     * * *;
341,ESC) Return to Previous Menu;
342,Enter a selection number, then hit the RETURN key >>> ;
343,ENTER A NEW TWO LETTER COMMAND FOR BUTTON # ;
344,*****  SELECT VIDEO GRAPHICS BOARD  *****;
345,IS GRAPHICS TO BE DISPLAYED ON: ;
346,(1) FIRST (SINGLE) SCREEN ?;
347,(2) SECOND SCREEN ?;
348,ENTER SELECTION 1 OR 2 >> ;
349,SHOULD CONTROL TEXT BE DISPLAYED ON: ;
350,(1) FIRST SCREEN ?;
351,(2) SECOND (GRAPHICS) SCREEN ?;
352,ENTER SELECTION 1 OR 2 >> ;
353,*****  LOCATE THE DIGITIZER MENU  *****;
354, YOU MUST CONFIGURE THE DIGITIZER FIRST !!;
355,Enter the Menu Number (1 - 10) >>> ;
356,Digitize lower left corner of Digitizer Menu >>> ;
357,Digitize upper right corner of Digitizer Menu >>> ;
358,How many horizontal boxes are in the Menu? > ;
359,How many vertical boxes are in the Menu? > ;
360,DIGITIZER MENU LIMITED TO 500 ENTRIES !! ;
361,ENTER NEW ;
362,ENTER NEW ;
363,******   G E N E R I C  ---  C A D D   ****** ;
364,Level 3 ;
365,CHANGE ;
366, (;
367,)  LIMITS: ;
368, TO ;
369, > ;
370,DECIMAL PRECISION ;
371,CURSOR COLOR ;
372,DISPLAY TEXT COLOR ;
373,LINE COLOR ;
374,TEXT COLOR ;
375,FILL COLOR ;
376,HATCH COLOR ;
377,DIMENSION COLOR ;
378,SET ;
379,FRACTIONS (2,4,8,16,32,64) (;
380, ) > ;
381, < BLACK > ;
382,( 1 = HORIZONTAL, 2 = ALIGNED );
383,( 1 = INLINE, 2 = OVERLINE );
384,(WITNESS);
385,   ( WORKING... );
386,OLD ( CONFIG.FIL ) DETECTED... New file created if changes saved;
387,6) Pen Sort is ;
388,(4) LPT2  ;
389,(5) LPT3  ;
390,LPT;
391,COM;
392,ENTER MOUSE SPEED 1 = FASTEST  16 = SLOWEST (1 - 16) >> ;
393,6) Display READ.ME file ;
394,7) Display Video Information ;
395,*** PRESS ANY KEY TO CONTINUE, [ESC] TO QUIT *** ;    
396,Slash Head;
397,File not found.  Please put SUPPLEMENTAL OR CONFIG DISK in drive A:.;
398,(3) BUS MOUSE;
399, v 1.1.3;
