     There are 10 new printer drivers for HP laser printers. 
     Some drivers are intended to replace the old drivers, while
     others have been included to add new functionality.
     
     Following are the problems addressed by the new drivers: 
     
     1.  The following drivers will print in the non-printable
     area of the paper when printing within a program or from the
     dot prompt: 
     
          HPLAS100.PR2
          HPLAS2I.PR2
          HPLAS2ID.PR2
     
     For example, the output produced by executing a LIST TO
     PRINT  command will have some lines missing if the output
     runs across two pages.  The following drivers are intended
     to replace those printer drivers:
     
          HPLAR100.PR2   Replaces  -------->      HPLAS100.PR2 
          HPLAR2I.PR2    Replaces  -------->      HPLAS2I.PR2
          HPLAR2ID.PR2   Replaces  -------->      HPLAS2ID.PR2
     
     These new drivers prints almost identically to the ones
     before at 66 lines per page (letter size paper), but the
     first printable line is now one line higher.
     
     2.  The  HPLASL.PR2 (landscape driver) may print in the
     non-printable area of the page with both reports or
     programs.  The problem can be resolved within reports by
     inserting blank lines in the header and  footer bands.  To
     eliminate the problem, you can use the new landscape driver
     for the HP LaserJet:
     
          HPLASL45.PR2
     
     This new driver sets the lines per page to 45, which will
     produce a top and bottom margins of three lines.  To get
     proper pagination, you must set the page length to 45.
     
     3.  It is not possible to print labels properly with the
     drivers listed below:
     
          HPLAS100.PR2
          HPLAS2I.PR2
          HPLAS2ID.PR2
     
     Since the above drivers change the VMI (line spacing)
     setting to 7.4/48 of an inch (6.48 lines per inch instead of
     6 lines per inch) it is next to impossible or difficult to
     line up the labels properly. All the parameters on the
     Dimension menu in the label design are based on 6 lines per
     inch.  The new drivers listed below use VMI of 6 lines per
     inch with top and bottom margin of 3.  The new drivers set
     the lines per page to 60 (letter size paper), so for proper
     pagination, you must set the page length to 60.
     
          HPLAS60.PR2
          HPLAS260.PR2
          HPLAD60.PR2
     
     4.  With all the old HP Laserjet printers, when printing a
     line with more than one object on the same line to be
     boldfaced, for example field headings in a report, only the
     first object will be printed in boldface. The following HP
     LaserJet drivers have been changed to access the internal
     boldface font of the printer:
     
          HPLAS260.PR2
          HPLAD60.PR2
          HPLAR2I.PR2
          HPLAR2ID.PR2
          HPL245.PR2   
      
     The bold attribute will be ignored by the printer if a bold
     attribute is not available for the font in use.  The drivers
     for the original HP Laserjet printer do not support this
     method, because they do not have an internal boldface font. 
     The HP series II and IID, however, have internal boldface.
     
     5.  The landscape driver HPLASL.PR2, is intended for the
     original HP laserJet, which does not support the IBM
     Character set for line and box drawing.  The new landscape
     driver for the HP series II and IID (in simplex mode) is:
     
          HPLS2L45.PR2
     
     It does support the IBM character set for line and box
     drawing. The driver sets the lines per page to 45, so for
     proper pagination, you must set the page length to 45.
      
     ********************************************************************************
     
     Following is a brief description of the new printer drivers
     for the HP LaserJet printer family.
     
     HPLAR2I.PR2
     
     This driver is intended for the HP LaserJet Series II, IID
     (simplex mode) or compatible printers and it replaces the
     original HPLAS2I.PR2 driver.  It fixes the problem of
     printing in the non-printable area of the paper by enabling
     skip over perforation.  Set the lines per page to 66 (letter
     size paper), when using this driver.  In addition, the
     internal bold face font is supported.
     
     HPLAR100.PR2
     
     This driver is intended for the HP LaserJet or compatible
     printers and it replaces the original HPLAS100.PR2 driver. 
     It addresses the problem of printing in the non-printable
     area of the paper by enabling skip over perforation.  Set
     the lines per page to 66 (letter size paper), when using
     this driver.
     
     HPLAR2ID.PR2
     
     This  driver is intended for the HP LaserJet Series IID or
     compatible printers and it replaces the original
     HPLAS2ID.PR2 driver.  It fixes the problem of printing in
     the non-printable area of the paper by enabling skip
     perforation.  Set the lines per page to 66 (letter size
     paper), when using this driver.  In addition, the internal
     bold face font is supported.
     
     HPLAS260.PR2
     
     This  driver is intended for the HP LaserJet Series II, IID
     (simplex mode) or compatible printers.  It prints at 6 lines
     per inch, making it suitable for printing labels.  The
     default for  top and bottom margin is set to 3 lines.  Set
     the lines per page to 60 (letter size paper), when using
     this driver.  In addition, the internal bold face font is
     supported.
     
     HPLAS60.PR2
     
     This  driver is intended for the HP LaserJet or compatible
     printers.   It prints at 6 lines per inch, making it
     suitable for printing labels. The default for  top and
     bottom margin is set to 3 lines. Set the lines per page to
     60  (letter size paper), when using this driver. 
     
     HPLAD60.PR2
     
     This  driver is intended for the HP LaserJet Series IID or
     compatible printers.  It prints at 6 lines per inch, making
     it suitable for printing labels. The default for  top and
     bottom margin is set to 3 lines. Set the lines per page to
     60  (letter size paper), when using this driver.  In
     addition, the internal bold face font is supported.
     
     HPLS2L45.PR2
     
     This  driver is intended for the HP LaserJet Series II, IID
     (simplex mode) or compatible printers.  It prints in
     landscape mode at 6 lines per inch, it also avoids printing
     in the non-printable area. The default for  top and bottom
     margin is set to 3 lines.  Set the lines per page to 45,
     when using this driver.  In addition, the internal bold face
     font is supported.  The IBM character set for line and box
     drawing is supported.
     
     HPLASL45.PR2
     
     This  driver is intended for the HP LaserJet or compatible
     printers.  It prints in landscape mode at 6 lines per inch,
     it also does not print in the non-printable area. The
     default for top and bottom margin is set to 3 lines.  Set
     the lines per page to 45, when using this driver.
