Unzip the file ZCOMLITE.ZIP with  PKUNZIP 2.04g or higher.

You will have the following files:
   ZCOMLITE.GEO
   STREAMC.GEO
   README.TXT

First you must create a directory in which to place ZComm Lite.  The directory
you need to create is \GEOWORKS\WORLD\ZCOMM.  This directory can be on your
B: drive or on the C: drive (PCMCIA card).  If placing on the C: drive, you
MUST create all of the directories specified.  If you intend on using an
internal PCMCIA modem, such as the AMT StarCard, then you MUST create the
directory on your B: drive.

Next place the file ZCOMLITE.GEO in the ZCOMM directory you just created.

Lastly place the file STREAMC.GEO file in the Zoomers B:\GEOWORKS\SYSTEM
directory.

To run ZComm Lite, use the Launcher hard icon, select ZCOMM and then select
ZComm Lite.  After the initial greetings dialog box, you are presented with
another dialog box requesting you select a default COMM port.  If you are using
an external modem select the RS-232 option.  If you are using an internal
PCMCIA modem card, select PCMCIA.
    *** Note, the only PCMCIA modem I have been able to test with is the new
        AMT StarCard.  I have not tested the modem to DEATH, but tests that
        I have done show the modem works well.

MENU OPTIONS
  FILE
    Send File         - Allow sending of an ASCII file
    Receive File*     - Currently disabled
    Capture Off/On    - Allows specification of a capture file to open/close
    eXit              - Shutdown ZComm Lite

  Comm
    Hang Up           - Drops DTR for 5 seconds
    Send Ctrl-C       - sends Control C out serial port
    Clear XOFF        - sends XOn (Ctrl-Q) out serial port
    Send Misc         - sends Misc field of current DD record
    Initialize Modem  - sends initialization sequence to modem
    Redial Last       - redials the last selected phone number

  Window
    Dialing Directory - brings up DD phone list
    Settings ->       - allows setting communication parameters
      Com Port
      Baud Rate
      Parity Bits
      Length
      XStop Bits
      Mode
      Protocol

  Help
    Content*          - currently disabled
    About             - displays the About dialog box
    Info              - displays diag info for ZComm Lite


  All of the above options are self explanatory except for Dialing Directory.
ZComm Lite allows you to keep four phone entries for your most often called
phone numbers.  Each Phone Directory record contains four fields.  Those fields
are: Name, Phone, Params and Misc.
    Name   is not currently used by ZComm Lite other than to give the user a
           descriptive title for the record.
    Phone  contains the phone number to call.
    Params is not currently used, it's intended purpose is to allow the user
           to define on a record by record basis how the communication port
           should be setup.
    Misc   currently, is usable by Zcomm Lite for sending of passwords, etc.
           to host systems.  As an example, if one of your entries was for
           Compuserve, you would place your UserID and Password in the Misc
           field.  Then when you receive the ID: prompt you would select
           menu option Comm | Send Misc and it would send the info.  For this
           example Misc would look like '7xxxx,xxxx/cccccccccc'.

  The buttons on the bottom of the dialog box have the following uses:
      'Nxt' and 'Prv' buttons to navigate and display each record. 
      'Save' button to save any changes to a record.
      'Ok' button to call the currently viewed record.
      'Quit' button to cancel without calling.

DISCLAIMER
  I have tested this program pretty completely both in simulation and on my
own Zoomer.  I have had no problems, but then I wrote the program and I know
what I should do and not do.
  That having been said, I must make the following disclaimer statement.
  I will not be held legally or monitarily responsable for any damages or loss
of data incurred thru the use of ZComm Lite.  Use it at your own risk.


  All that having been said, ENJOY.  ZComm Lite, being a FREEWARE program,
will have no further features added.  It will be maintained and any bugs
reported to me will be fixed in future revisions.

  For a full feature laden version watch for the announcement of the 
Commercial shrink wrapped version called ZComm Pro.

  Thanks,

     Kerry W. Podolsky
     Structured Software Designs
     41 Brandywine Dr.
     Mastic, NY  11950
     Voice/Fax: (516) 281-4939
     CIS:  70521,3000




