
			http://members.aol.com/easydesk
			Easy Desk Software
			easydesk@aol.com
			(516)587-9015

	Please read this file before installing WinSafe95. 
	If you have any questions or need any assistance 
	please contact us via E-mail or phone.
	We will responsed to E-mail the same day.

	The setup program must be used to install WinSafe95. Follow these
	instructions carefully!
	Due to the vast differences in computer hardware and software
	WinSafe95 must be programed to your individual computer.
	WinSafe95 looks for and reads all Hidden files. Most
	other programs will bypass Read Only and Hidden files(Read Only
	and Hidden are attributes).
	WinSafe95 is one of the most advanced backup utilities available.
	WinSafe95 will fix small problems as well as most major crashes. 

	WinSafe95 will not work properly if you do not use the
	Setup Program and then follow the steps below. 
	
	If you reinstall WinSafe 95 you must uninstall WinSafe95 first, use 
	the Uninstall command under UTILITIES on the menu bar. Besure all 
	Windows programs are closed. 
	
	WinSafe95 will tell you when the installation is complete.
	You will need to restart your computer to complete the installation. 
	
	                      HOW TO INSTALL:
	1) Run the setup program. If a MSDOS window stays open 
	   at the end of the setup program please close it and continue.

	2) Then access WinSafe95 from your desk top and on the menu bar click
	   on SETUP and then SETUP TEXT (This text file will appear).
	   YOU SHOULD NOW CLOSE THIS FILE.

	3) On the menu bar click on SETUP then START TEST.

	4) WinSafe95 will now look for non system hidden files. If it finds  
	   one, a message box will appear and tell you that WinSafe95 can not 
	   find a file, line 19 or 42. Winsafe95 will also prompt you to 
	   backup now. 
	   If the only message you get is Winsafe asking if you had any 
	   problems click YES not NO. Backup and go to step 11.

	5) Write the file name and path down on a piece of paper
	    ie:(c:\Windows\system.sys) and click OK.

	6) When WinSafe95 is complete click on SETUP and then ATTRIBUTE

	7) Type the file name and path in the next box to be displayed, and 
	   click OK.

	8) You will now see in the MSDOS window a line similar to the one
	   below:
	   "A     SHR      SYSTEM.DAT C:\WINDOWS\SYSTEM.DAT"
	   make note of the letters between the A and SYSTEM.DAT.
	   In the example the letters are SHR. Then close the MSDOS window.

	9) In then next window to appear type the letters that appeared
	   in the previous MSDOS window (without spaces), and click OK.
	   If in step 8 only an R was present type the letter R if no 
	   letter appeared click CANCEL.

	10) After you have completed step 9 with all files reported click on
	   SETUP on the menu bar and then on START TEST again. You should not 
	   receive any messages that WinSafe95 can not read a file. If you 
	   still get a message click on SETUP and then WINSAFE.INI Look for
 	   [HIDDEN] and verify that you have entered the correct file name
	   and path. Then repeat steps 3-9.

       11) Next click on the REPORT Button, This will take a few moments 
	   longer to finish then the Test did.

       12) When the Report is finished a window will appear and tell you
	   to click on TEST COMPLETE and to reboot. Close WinSafe95 and 
	   reboot. when you reenter Windows WinSafe may tell you to backup
	   and ask you again if you had any problems. Press No if you did not
	   have any and then click on BACKUP. 
	        	
	After rebooting the first time WinSafe95 will tell 
	you if it can not read a file. It will also ask you if it had
	any problems reading files, If you answers yes this Help file 
	will appear to show you how to adjust the startup time. Click No
	if you recieved no messages.
	    
	If WinSafe95 could not read a file when you restarted Windows
		go to step 13

	13) WinSafe95 can not read files that are in use. If you hear the 
	   hard drive still working when The WinSafe95 PLEASE WAIT window 
		appears: use the SETUP menu to increase the wait time. 
		The value is set to 7. Increasing the number will cause a 
		longer wait time and decreasing it will shorten wait time.
		WinSafe95 must wait till the hard drive stops working and all
		programs(i.g. virus scanners)have finished booting into 
		Windows Try rebooting before continuing. If you still
		get a message window that WinSafe95 can not read a file
		go to step 3.
	

	14) Backup after all programs have completely booted to Windows.
	    Be sure that Winsafe95 has stopped searching for files. 
	   You should not have an MSDOS windows staying open after the Setup 
	   is complete. 

	15) Note that you may not be able see the backup files because 
	they are all "hidden" to protect them for virus and user tampering.
	WinSafe95 will tell you when you need to make new backup files.
	
	16) Click on the MSD button if nothing happens then use the find 
	command at the start button and type msd.exe. If you find it place
	it in your windows directory.
	If your system does not have MSD.exe install on it; you will find 
	it on your Windows 95 cdrom. Use the Find feature at the Start 
	button. You may download this file from Mircosoft on the Internet 
	or from our web site file- Msd.zip
	Site address   http://members.aol.com/easydesk/our.htm

		SETUP IS NOW COMPLETED
	It is suggested that at this time you click on UTILITIES in the
	menu bar then on SYSTEM INFORMATION and print out that file.
	This is a very large file,so besure to have enough paper in your
	printer. If not at least print it to a file. This file contains
	all the configurations of your system, if you crash because of 
	hardware failure you will need this file.
	
	There are two other text files available for reading. The HELP
	text  and the Restore text.
ECHO is off
