Dual NAM Programming - Tandy Phones 
----------------------------------- 
SEC   = Security Code - as programmed where you bought the phone 
CLASS = 08            - for CT-102 or CT-1033 
 
    Type ...                  Display will show ... 
    
To enter Programming Mode ... 
    *3001* SEC [SEL] 9        'InStaLL' 
    [END]                     'IdEnt IF InFO Pri' 
 
If you want to program the first NAM press [END] to continue. 
If you want to program the second NAM ... 
    [SND]                     'IdEnt IF InFO Opt' 
    [END]                     'OptInFO disAbLEd'   (if disabled) 
    [SND]                     'OptInFO EnAbLEd'    (to enable NAM2) 
    [END]                     to continue 
 
After pressing [END] the first parameter 'HO-Id' will appear. 
Press [END]      to page through the parameters. (they should recycle) 
Press [SEL][CLR] to exit programming at any time. 
Numbric responses can be entered.  Use [SEL] to toggle 0-1 and A-b. 
 
Parameters 
   Home System ID              HO-Id     5 digits   00000-32767 
   Access Method               ACCESS    1 digit    Toggle 0-1 
   Local Control Option        LOCAL     1 digit    Toggle 0-1 
   Phone Number                Phone n  10 digits   As assigned 
   Station Class Mark          CLASS     2 digits   00-99 
   Home Paging Channel         PAGE Ch   3 digits   001-666 
   Overload Class              O-LOAd    2 digits   00-15 
   Prefered System             PrEF SYS  1 Char     Toggle A-b 
   Group ID                    GrouP     2 digits   00-15 
   Security Code               SEC       5 digits   00000-99999 
   ^^^ Warning: Remember this code or the phone MUST be sent to Texas 
		by Radio Shack at YOUR EXPENSE for it to be read!!! 
 
   Date 1 - Program Release    1dAtE     6 digits   mmddyy 
   ^^^ Warning: NEVER change this date.  NEVER!!! 
   Date 2 - Programming Date   2dAtE     6 digits   mmddyy 
   ^^^ Today's date. 
 
Remember to type [SEL][CLR] to exit program mode. 
 
 
Single NAM Programming - Tandy Phones 
------------------------------------- 
SEC   = Security Code - as programmed where you bought the phone  
CLASS = 00            - for CT-100 or CT-200 
CLASS = 08            - for CT-101 or CT-201 
CLASS = 10            - for CT-301 
    (CT-300 does not request a CLASS during programming.) 
 
    Type ...                  Display will show ... 
    
To enter Programming Mode ...  (CT-100 and CT-101) 
    *17*3001* SEC *           'HO-Id' 
 
To enter Programming Mode ...  (CT-200 and CT-201) 
    *17*1003* SEC *           'HO-Id' 
 
To enter Programming Mode ...  (CT-300 and CT-301) 
    *17*2001* SEC *           'HO-Id' 
 
After pressing the last '*' the first parameter 'HO-Id' will appear. 
Press [SEL]      to page through the parameters. (they do not recycle) 
Press [SEL][END] to exit programming early. 
 
Parameters 
   Home System ID              HO-Id     5 digits   00000-32767 
   Access Method               ACCESS    1 digit    0-1 
   Local Control Option        LOCAL     1 digit    0-1 
   Phone Number                Phone n  10 digits   As assigned 
   Station Class Mark          CLASS     2 digits   00-99 
   Home Paging Channel         PAGE Ch   3 digits   001-666 
   Overload Class              O-LOAd    2 digits   00-15 
   Group ID                    GrouP     2 digits   00-15 
   Security Code               SEC       4 digits   0000-9999 
   ^^^ Warning: Remember this code or the phone MUST be sent to Texas 
		by Radio Shack at YOUR EXPENSE for it to be read!!! 
       Note: SEC is 5 digits on CT-300 and CT-301 
 
Disclaimer: 
   Anyone tampering with the settings of the NAM is taking the risk 
   of rendering the phone UNUSABLE.  Be careful!  These instructions 
   are provided for information purposes only.  Please do not program 
   any phone with any number you are not authorized to use. 
