MOTOROLA CELL PHONES 
 
NOTES:  Some units have dual NAM's. 
        The ESN prefix is 130 decimal, 82 hex. 
        Motorola: 1-800-331-6456 
 
There are MANY different models of Motorola phones sold under various 
brand names, if you think it's a Motorola, it probably is. 
 
Determine which access sequence to use: 
 
HAND HELD PORTABLE MODELS 
 
If the phone has a FCN button and no MENU button use sequence 1. 
If the phone has no FCN button use sequence 2. 
If the phone has a MENU button and a FCN button use sequence 4. 
 
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS 
 
If the phone has no FCN button and no RCL button use sequence 3. 
If the phone has a FCN button use sequence 4. 
If the phone has a MEM button use sequence 5. 
If the phone has a RCL button and no FCN button use sequence 6. 
 
 
SEQUENCE#     ACCESS CODE 
 
1             FCN   (SECURITY CODE TWICE) RCL 
2             STO # (SECURITY CODE TWICE) RCL 
3             CTL 0 (SECURITY CODE TWICE) * 
4             FCN 0 (SECURITY CODE TWICE) RCL 
5             FCN 0 (SECURITY CODE TWICE) MEM 
6             CTL 0 (SECURITY CODE TWICE) RCL 
 
The default security code is 000000.  The CTL (control) button is the 
single black button on the side of the handset. 
 
 
NAM programing: 
 
1.  Turn the power on. 
 
2.  Within ten seconds enter the access sequence as determined above. 
 
3.  The phone should now show "01" in the left of the display, this is the 
    first programing entry step number.  If it does not the security code 
    is incorrect, or the programing lock-out counter has been exceeded.  In 
    either case you can still program the unit by following the steps under 
    TEST MODE PROGRAMING below. 
 
4.  The * key is used to increment each step: 
 
    Each time you press * the display will increment from the step number, 
    displayed on the left, to the data stored in that step, displayed on 
    the right.  When the data is displayed make any necessary changes and 
    press * to increment to the next step number. 
 
5.  The SND key is used to complete and exit programing when any STEP 
    NUMBER is displayed. 
 
    If you have enabled the second phone number bit in step 10 below then 
    pressing SND will switch to NAM 2.  Steps 01 thru 06, 09 and 10 will 
    repeat for NAM 2, the step number will be followed by a "2" to indicate 
    NAM two. 
 
5.  The CLR key will revert the display to the previously stored data. 
 
6.  The # key will abort programing at any time. 
 
 
PROGRAMING DATA: 
 
STEP#    #OF DIGITS/RANGE    DESCRIPTION 
 
01       00000 - 32767       SYSTEM ID 
02       3 DIGITS            AREA CODE 
03       7 DIGITS            TEL NUMBER 
04       2 DIGITS            STATION CLASS MARK 
05       2 DIGITS            ACCESS OVERLOAD CLASS 
06       2 DIGITS            GROUP ID (10 IN USA) 
07       6 DIGITS            SECURITY CODE 
08       3 DIGITS            LOCK CODE 
09       0333 OR 0334        INITIAL PAGING CHANNEL 
10       6 DIGIT BINARY      OPTION PROGRAMING (SEE NOTE 1) 
11       3 DIGIT BINARY      OPTION PROGRAMING (SEE NOTE 2) 
 
 
NOTES: 
 
Take care with Motorola's use of "0" and "1".  Some options use "0" to 
enable, some use "1". 
 
1.  This is a 6 digit binary field used to select the following options: 
 
    Digit 1:  Internal handset speaker, 0 to enable. 
    Digit 2:  Local Use Mark, 0 or 1. 
    Digit 3:  MIN Mark, 0 or 1. 
    Digit 4:  Auto Recall, always set to 1 (enabled). 
    Digit 5:  Second phone number (not all phones), 1 to enable. 
    Digit 6:  Diversity (Two antennas, not all phones), 1 to enable. 
 
2.  This is a 3 digit binary field used to select the following options: 
 
    Digit 1:  Continuous DTMF, 1 to enable. 
    Digit 2:  Transportable Ringer/Speaker, 0=Transducer, 1=Handset. 
    Digit 3:  8 hour time out in transportable mode, 0 to enable. 
 
 
On newer models, they have added and changed some numbers.  The numbers 
as of the 3/27/92 manual are as follows: 
 
1.  The 6 digit binary field is still the same.   
 
2.  The 3 digit binary field has become a 5 digit binary field. 
     
    Digit 1:  Failed Page Indicator                        1=Disabled;0=Enabled 
    Digit 2:  Motorola Enhanced Scan                       1=Enabled; 
0=Disabled 
    Digit 3:  Long Tone DTMF                               1=Enabled; 
0=Disabled 
    Digit 4:  Transportable Internal Ringer Speaker        1=Handset; 
0=Transdcr 
    Digit 5:  Eight Hour Timeout                           1=Disabled;0=Enabled 
 
 
 
                              TEST MODE ACCESS: 
 
 
 
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS 
 
To enter test mode on units with software version 85 and higher you must 
short pins 20 and 21 of the transceiver data connector.  An RS232 break out 
box is useful for this, or construct a test mode adaptor from standard 
Radio Shack parts. 
 
For MINI TR or Silver Mini Tac transceivers (smaller data connector) you 
can either short pins 9 and 14 or simply use a paper clip to short the 
hands free microphone connector. 
 
HAND HELD PORTABLE MODELS: 
 
There are two basic types of Motorola portable phones, the Micro-Tac series 
"Flip" phones, and the larger 8000 and Ultra Classic phones.  Certain newer 
Motorola and Pioneer badged Micro-Tac phones do not have a "flip", but 
follow the same procedure as the Micro-Tac. 
 
8000 & ULTRA CLASSIC SERIES: 
 
If you have an 8000 series phone determine the "type" before trying to 
enter test mode.  On the back of the phone, or on the bottom in certain 
older models, locate the F09... number this is the series number.  If the 
FOURTH digit of this number is a "D" you CAN NOT program the unit through 
test mode, a Motorola RTL4154/RTL4153 programer is required to make any 
changes to this unit. 
 
Having determined that you do not have a "D" series phone the following 
procedure is used to access test mode: 
 
Remove the battery from the phone and locate the 12 contacts at the top 
near the antenna connector.  These contacts are numbered 1 through 12 from 
top left through bottom right.  Pin 6, top right, is the Manual Test Mode 
Pin. You must ground this pin while powering up the phone.  Pin 7 (lower 
left) or the antenna connector should be used for ground.  Follow one of 
these procedures to gain access to pin 6: 
 
1.  The top section of the battery that covers the contacts contains 
nothing but air.  By careful measuring you can drill a small hole in the 
battery to gain access to pin 6, alternately simply cut the top off the 
battery with a hack saw.  Having gained access use a paper clip to short 
pin six to the antenna connector ground while powering up the phone. 
 
2.  If you do not want to "destroy" a battery you can apply an external 7.5 
volts to the + and - connectors at the bottom of the phone, ground pin 6 
while powering up the phone as above. 
 
3.  You can also try soldering or jamming a small jumper between pins 6 and 
7 (top right to lower left), or between pin 6 and the antenna connector 
housing ground.  Carefully replace the battery and power up the phone.  Use 
caution with this method not to short out any other pin. 
 
4.  A cigarette lighter adaptor, if you have one, also makes a great test 
mode adaptor as it can be disassembled to give you easier access to pin 6. 
Many are pre marked, or even have holes in the right location.  This is 
because they are often stamped from the same mold that the manufacturer 
uses for making hands free adaptor kits and these kits require access to 
the phone's connectors. 
 
               /  Antenna Housing 
           ZDD? 
     ZDDDDDEDDEDDDDD? 
     3*    3  3    *3 
     CDDDDDABBADDDDD4      To enter test mode, ground pin 6 to either pin 7 
     3H H HZY@?H H H3      or the antenna housing.  I personally rapped a  
     3H H H@DDYH H H3      paper clip around the antenna housing and bent it  
     CDDDDDDDDDDDDDD4      so it *ALMOST* touched the test pin.  All I had  
     3 Back of phone3      to do was push the paper clip a little when I   
     3 with battery 3      turned the phone on. 
     3 removed.  The3 
     3 H is a pin.  3 
     3              3 
     3 Counting at  3 
     3 the top left 3 
     3 to right.    3 
     3              3 
     31 2 3    4 5 63 
     37 8 9   1011123 
     3              3 
     3              3 
     3* ZD?    ZD? *3 
     @DDADADDD-ADADDY 
 
 
 
MICRO-TAC "FLIP" SERIES: 
 
This phone follows similar methods as outlined for the 8000 series above. 
 
Remove the battery and locate the three contacts at the bottom of the 
phone, the two outer contacts are raised and connect with the battery.  The 
center contact is recessed, this is the Manual Test Mode connector. 
 
Now look at the battery contacts, the two outer ones supply power to the 
phone, the center contact is an "extra" ground.  This ground needs to be 
shorted to the test mode connector on the phone.  The easiest way to do 
this is to put a small piece of solder wick, wire, aluminum foil or any 
other conductive material into the recess on the phone.  Having done this 
carefully replace the battery and turn on the power, if you have been 
successful the phone will wake up in test mode. 
 
           ZDDD? 
           3   3 
         ZDADDDADDDDDDDDDDDDDDDDD? 
         3                       3 
         3DDDDDDDD?     ZDDDDDDDD3 
         3        @DDDDDY        3 
         3                       3 
         3 Flip phone with       3 
         3 battery removed.  The 3 
         3 H's are pins.  Pin    3 
         3 2 is the test pin and 3 
         3 is recessed.  Put     3 
         3 something in the      3 
         3 recess so it touches  3 
         3 the battery.          3 
         3                 1 2 3 3 
         3                       3 
         3                 H H H 3 
         @DDDDDDDDDDDDDDDDDDDDDDDY 
 
 
GENERAL NOTES: 
 
HANDSETS:  Most Motorola handsets are interchangeable, when a handset is 
used with a transceiver other than the one it was designed for the display 
will show "LOANER".  Some features and buttons may not work, for instance 
if the original handset did not have a RCL or STO button, and the 
replacement does, you will have to use the control * or control # sequence 
to access memory and A/B system select procedures. 
 
 
 
LOCK/UNLOCK PROCEDURES: 
 
     Phones with "LOCK" buttons:  Press lock for at least 1/2 a second. 
 
     Phones with a "FCN" button:  Press FCN 5, note that 5 has the letter's 
                                  "J,K, and L" for lock. 
 
     Phones with no FCN or LOCK button:  Press Control 5, control is the black 
                                         volume button on the side of the 
                                         handset. 
 
 
SYSTEM SELECT PROCEDURES: 
 
     Phones with a RCL button:  Press RCL *, then * to select, STO to store. 
 
     Phones with no RCL button: Press Control * then * to select, # to store. 
 
     Options are:    CSCAn:    Preferred/Non preferred with system lockout. 
                     Std A/b, or Std b/A:  Preferred/Non preferred. 
                     SCAn Ab, or SCAn bA:  Non preferred/Preferred 
                     SCAn A:  "A" ONLY 
                     SCAn b:  "B" ONLY 
                     HOME:     Home only 
 
     (these are typical options, some phone's vary.  C-Scan is only available  
     on newer models and does not appear unless programed, see below.) 
 
 
 
 
                                 TEST MODE 
     
     
    Taken from the July 1993 Cellular Subscriber Technical Training Manual 
    Item# 68P09300A60-C and the Curtis Namfax vol.4.  I believe this is a 
    complete listing of all the commands that were ever possible.  This  
    includes old phones and the new ones.  If there are two entries for a 
    particular number, the first one is the current command and the second 
    is for older models. 
 
NOTE: Not all commands work on all telephones.  If a command is not valid the 
      display will show "ErrOr."  Not all numbers have been assigned.  Not all 
      numbers have been listed here.  Some commands were intended only for 
      Motorola factory applications.   (This is the disclaimer in the 
      technical training manual.  I have included all of the other commands I  
      have discovered one way or another.  I do believe this is a complete list 
      of the commands.) 
     
 
Three test commands are significant for programming and registering the 
the telephone for service:  see full descriptions under TEST MODE COMMANDS. 
 
32#  Clears the telephone.  (Older Motorola allowed either three or fifteen  
changes in the MIN.  After that, the phone had to be sent to Motorola to reset  
the counter.  This is the command they use.)  
 
38#  Displays the ESN 
 
55#  This is the TEST MODE PROGRAMMING (as described below). 
 
 
                          TEST MODE COMMANDS: 
 
 
#    Enter Test Command Mode 
 
00#  no function 
 
01#  Restart (Re-enter DC power start-up routine.)  On TDMA telephones, this 
     command has the same effect as pressing the PWR button. 
 
02#  Display Current Telephone Status (This is a non-altering version of the 
     STATUS DISPLAY.  On a 14 character display, all the information is shown. 
     On a 7 character display only the information on the second line of a 14 
     character display is shown.  On a 10 character display, all the  
     information on the second line of a 14 charcter display plus the last  
     three characters of the first line are shown.) 
 
     STATUS DISPLAY, ALTERNATES BETWEEN: 
      
     AAA BBB   AAA = Channel Number (decimal)    BBB = RSSI reading for channel 
     CDEFGHI   are as follows: 
 
     C = SAT frequency (0=5970, 1=6000, 2=6030, 3=no channel lock) 
     D = Carrier (0=off, 1=on) 
     E = Signalling tone (0=off, 1=on) 
     F = Power attenuation level (0 through 7) 
     G = Channel mode (0=voice channel, 1=control channel) 
     H = Receive audio mute (0=unmuted, 1=muted) 
     I = Transmit audio mute (0=unmuted, 1=muted) 
 
     Press * to hold display and # to end. 
 
03#  Reset Autonomous Timer.   This command results in the reset of the  
     autonomous timer but does not provide any test function on these models. 
 
04#  Initializes Telephone to Standard Default Conditions: 
     Carrier Off, Power Level 0, Receiver Audio Muted, Transmit Audio Muted, 
     Signalling Tone Off, SAT Off, Resetting of Watch-Dog Timer Enabled,  
     DTMF and Audio Tones Off, Audio Path Set to Speaker 
 
05#  TX Carrier On (Key Transmitter) 
 
06#  TX Carrier Off 
 
07#  RX Audio Off (Mute Receiver Audio) 
 
08#  RX Audio On (Unmute Receiver Audio) 
 
09#  TX Audio Off 
 
10#  TX Audio On 
 
11(Ch.No.)# Set Tranceiver to Channel xxxx (Receive and Transmit in Decimal; 
            accepts 1, 2, 3, or 4 digits) 
 
12x# Set Power Step to x; (0,1-7) 0=Maximum Power (3 Watts) 7=Minimum Power Out 
 
13#  Power Off (Shuts off the radio) 
 
14#  10 kHz Signalling Tone On 
 
15#  10 kHz Signalling Tone Off 
 
16#  Setup  (Transmits a five word RECC message; each of the five words will  
     be "FF00AA55CC33."  Transmitter de-keys at the end of the message.) 
 
17#  Voice  (Transmits a two word REVC message; each of the two words will be 
     "FF00AA55CC33."  Transmitter de-keys at the end of the message.) 
 
18#  C-Scan  (Allows for entry of as many as 5 negative SID's for each NAM.) 
 
     Newer Motorola phones are equipped with a feature called C-Scan, this is  
     an option along with the standard A/B system selections.  C-Scan allows  
     the phone to be programed with up to five inhibited system ID's per NAM.   
     This is designed to prevent the phone from roaming onto specified non-home 
     systems and therefore reduce "accidental" roaming fees. 
 
     1.  C-Scan can only be programed from test mode, power phone up with the 
         relevant test mode contact grounded (see above). 
 
     2.  Press # to access test mode. 
 
     3.  Press 18#, the phone will display "0    40000". 
 
     4.  Enter the first inhibited system ID and press *. 
 
     Continue to enter additional system ID's if required.  After the 5th entry 
     the phone will display "N2". Press * to continue and add system ID's for 
     NAM 2 as required. 
 
     5.  If an incorrect entry is made (outside the range of 00000-32767) the 
         display will not advance, press CLR and re-enter.  Use a setting of 
         40000 for any un-needed locations. 
 
     6.  When the last entry has been made press * to store and press # to 
exit, 
         turn off power. 
 
     or 
      
     [**Phones without the C-Scan option used this command to SEND NAM.**] 
 
18#  SEND NAM.  Display shows AA BB.  Where AA=Address and BB=Data.  Displays   
 
     the contents of the NAM, one address at a time, advanced by pressing the 
     * key.  The following data is contained in NAM.  The test is exited by 
     depressing the # key. 
     SIDH                 Sec. Code 
     OPT. (1,2,&3)        MIN 
     MIN1, MIN2           FCHNA 
     SCM                  FCHNB 
     IPCH                 NDED 
     ACCOLC               CHKSUM       GIM 
 
19#  Display Software Version Number  (4 digits displayed as year and week) 
 
NOTE:  Entering commands 20# through 23# or 27# causes the tranceiver to begin 
       a counting sequence or continous transmission as described below.  In 
       order to exit from the commands to enter another test command, the #  
       key must be depressed; all other key depressions are ignored. 
 
20#  Receive control channel messages counting correctable and uncorrectable 
     errors.  When the command starts, the number of the command will be  
     displayed in the upper-right corner of the display.  Entering a # key 
     will terminate the command and display two three-digit numbers in the  
     display.  The first number is the number of correctable errors and the 
     second is the uncorrectable errors. 
 
21#  Received voice channel messages counting correctable and uncorrectable 
     errors.  When the command starts, the number of the command will be  
     displayed in the upper right-hand corner of the display.  Entering a #  
     key terminates the command and will display two three-digit numbers in  
     display.  The first is the number of correctable errors and the second  
     is the uncorrectable errors. 
 
22#  Receive control channel messages counting word sync sequence.  When the 
     command starts, the number of the command will be displayed in the upper 
     right-hand corner of the display.  Entering a # key will terminate the 
     command and display the number of word sync sequences in the display. 
 
23#  Receive voice channel messages counting word sync sequences.  When the 
     command starts, the number of the command will be displayed in the upper 
     right-hand corner of the display.  Entering a # key will terminate the  
     command and display the number of word sync sequences in the display. 
 
24#  Receive control channel data and display the majority voted busy/idle 
     bit.  0=idle  1=busy 
 
25x# SAT On         When                        x=0, SAT=5970HZ 
                                                x=1, SAT=6000HZ 
                                                x=2, SAT=6030HZ 
 
26#  SAT Off 
 
27#  Transmit Data  (Transmits continuous control channel data.  All words  
     will be "FF00AA55CC33."  When the command starts, '27' will be displayed 
     in the right side of the display.  Entering a # key will terminate the 
     command.  The transmitter de-keys when finished.) 
 
28#  Activate the high tone (1150 Hz +/- 55 Hz) 
 
29#  De-activate the high tone 
 
30#  Activate the low tone (770 Hz +/- 40 Hz) 
 
31#  De-activate the low tone 
 
32#  Clear (Sets non-volatile memory to zeroes or factory default.  This  
     command will affect all counters, all repertory memory including the last 
     number called stack, and all user programmable features including the 
     setting of System Registration.  It does not affect the ESN, NAM, phasing 
     data, or lock code.  This takes a minute or so.  DO NOT TURN OFF THE  
     TELEPHONE WHILE THIS IS SHOWING '32' ON THE DISPLAY.  WAIT UNTIL THE  
     NORMAL SERVICE LEVEL DISPLAY RESUMES!) 
 
33x# Turn on DTMF for x  (1-9, *, 0, #, plus the single tones)      
        Where x=1    697 Hz + 1209 Hz       10  697 Hz 
                2    697 Hz + 1336 Hz       11  770 Hz 
                3    697 Hz + 1477 Hz       12  852 Hz 
                4    770 Hz + 1209 Hz       13  941 Hz 
                5    770 Hz + 1336 Hz       14  1150 Hz (not used in cellular) 
                6    770 Hz + 1477 Hz       15  1209 Hz  
                7    852 Hz + 1209 Hz       16  1336 Hz 
                8    852 Hz + 1336 Hz       17  1477 Hz 
                9    852 Hz + 1477 Hz       18  1633 Hz (not used in cellular) 
                *    941 Hz + 1209 Hz 
                0    941 Hz + 1336 Hz 
                #    941 Hz + 1477 Hz 
 
34#  Turn DTMF Off 
 
35#  Display RSSI ("D" Series Portable Only) 
 
     or 
 
35x# Set Audio Path to x    x=0, V.S.P Microphone (Applies to mobiles only.) 
                            x=1, Speaker 
                            x=2, Alert 
                            x=3, Handset 
                            x=4, Mute 
                            x=5, External Telephone (Applies to Portables Only) 
                            x=6, External Handset (Applies to NEWER Portables) 
 
36nnn# Scan (TDMA Telephones only.  Scans the primary control channels and  
     attempts to decipher the forward data stream.  The display will show PASS1 
     if the strongest control channel was accessed, PASS2 if the second  
     strongest was accessed, and FAIL if no control channel could be accessed.) 
 
     (nnn=Scan speed in milliseconds).  Tunes from channel 1 to 666 in order. 
     Entering a * pauses the scan and displays current Channel Number and 
     RSSI reading (AAA=Channel Number and BBB=RSSI Reading).  When scan speed 
     is 300 milliseconds or greater, the current status is displayed during the 
     scan; when less than 300 milliseconds the status is displayed only during 
     pause.  Entering * during a pause causes the scan to resume.  Entering # 
     aborts the scan and leaves the mobile tuned to the current channel.  
During 
     this command only the * and # keys are recognized. 
 
37#  no function 
 
38#  Display ESN (Displays ESN in four steps, two hexadecimal digits at a time 
     in a for digit display.  The decimal shows the address, 00 through 03 as 
     the first two digits, and two digits of the ESN as the last two digits. 
     Use the 'G' to step through the entire hexadecimal ESN.) 
 
     Compander OFF ("D" Series Portables) 
 
     or 
 
38#  SND-SNM.  Display shows AA BB.  Where AA=Address;BB=Data.  Send the SNM 
     to the display.  All 32 bytes of the SNM will be displayed, one byte at  
     a time.  The byte address will be displayed in the upper right-hand 
     corner and the contents of that address will be displayed in the hex.   
     The * key is used to step through the address similar to the SEND-NAM 
     (18#) command. 
 
39#  Compander ON ("D" Series Portables) 
 
     or 
 
39#  RCVSU.  Receive one control channel word.  When the word is received it 
     is displayed in hex.  This command will be complete when a control channel 
 
     word is received or when the # key is entered to abort the command. 
 
40#  RCVVC.  Receive one voice channel word.  When the word is received it is 
     displayed in hex.  This command will be complete when a voice channel 
     word is received or when the # key is entered to abort the command. 
 
41#  Enables Diversity (On F19CTA... Series only.) 
 
42#  Disables Diversity (On F19CTA... Series only.) 
 
43#  Disable Diversity 
     USE T/R ANTENNA (On F19CTA... Series only.)   
     USE R ANTENNA (On D.M.T./ Mini TAC) 
 
44#  Disable Diversity 
     USE R ANTENNA (On F19CTA... Series only.)   
     USE T/R ANTENNA (On D.M.T./ Mini TAC)  
 
45#  Display Current RSSI (Displayed as a three-digit decimal number)    
 
46#  Display Cumulative Call Timer 
 
47x# Set RX Audio level to X 
     (For F19CTA ...Series Tranceivers)  
                                       X=0, Lowest Volume 
                                       X=6, Highest Volume 
                                       X=7, mute 
                                       Normal setting is 4. 
     (For D.M.T./ Mini TAC Tranceivers) 
                                       X=0, Lowest Volume 
                                       X=7, Highest Volume 
                                       Normal setting is 4. 
     (For TDMA Tranceivers and F09F... Series and Higher Portables) 
                                       X=0, Lowest Volume 
                                       X=15, Highest Volume 
                                       Normal setting is 2 to 4.  (On TDMA 
                                       Tranceivers and Micro TAC portables,  
                                       settings 8 through 15 are for DTMF 
                                       applications only.) 
 
48#  Side Tone On.  Use this command in conjunction with 350# to test the  
     entire audio path in hands-free applications. 
 
49#  Side Tone Off 
 
50#  Maintenance data is transmitted and test results displayed: 
     PASS=received data is correct 
     FAIL 1=2second timeout, no data rec. 
     FAIL 2=received data is incorrect 
 
51#  Test of mobile where maintenance data is transmitted and looped back.   
     Display is as follows: 
     PASS=looped-back data is correct 
     FAIL 1=2 second timeout, no looped-back data 
     FAIL 2=looped-back data is incorrect 
 
52x# SAT Phase Adjustment.  A decimal value that corresponds to phase shift 
     compensation in 4.5 degree increments.  Compensation added to inherent 
     phase shift in tranceiver to achieve a total of 0 degrees phase shift. 
 
     Do NOT enter any values except those shown below. 
 
     0 degrees = 0          121.5 degrees = 59           243.0 degrees = 86 
     4.5       = 1          126.0         = 60           247.5         = 87 
     9.0       = 2          130.5         = 61           252.0         = 112 
     13.5      = 3          135.0         = 62           256.5         = 113 
     18.0      = 4          139.5         = 63           261.0         = 114 
     22.5      = 5          144.0         = 40           265.5         = 115 
     27.0      = 6          148.5         = 41           270.0         = 116 
     31.5      = 7          153.0         = 42           274.5         = 117 
     36.0      = 16         157.5         = 43           279.0         = 118 
     40.5      = 17         162.0         = 44           283.5         = 119 
     45.0      = 18         166.5         = 45           288.0         = 120 
     49.5      = 19         171.0         = 46           292.5         = 121 
     54.0      = 20         175.5         = 47           297.0         = 122 
     58.5      = 21         180.0         = 64           301.5         = 123 
     63.0      = 22         184.5         = 65           306.0         = 124 
     67.5      = 23         189.0         = 66           310.5         = 125 
     72.0      = 48         193.5         = 67           315.0         = 126 
     76.5      = 49         198.0         = 68           319.5         = 127 
     81.0      = 50         202.5         = 69           324.0         = 104 
     85.5      = 51         207.0         = 70           328.5         = 105 
     90.0      = 52         211.5         = 71           333.0         = 106 
     94.5      = 53         216.0         = 80           337.5         = 107 
     99.0      = 54         220.5         = 81           342.0         = 108 
     103.5     = 55         225.0         = 82           346.5         = 109 
     108.0     = 56         229.5         = 83           351.0         = 110 
     112.5     = 57         234.0         = 84           355.5         = 111 
     117.0     = 58         238.5         = 85           360.0         = 70 
               
53#  Enable scrambler option, when equipped. 
 
54#  Disable scrambler option, when equipped. 
 
55#  Display/Program N.A.M. (Test Mode Programming) 
 
     TEST MODE PROGRAMING: 
 
     Assuming you have completed one of the above steps correctly the phone 
     will wake up in test mode when you turn the power on.  When you first 
     access test mode the phone's display will alternate between various status 
     information that includes the received signal strength and channel number. 
     The phone will operate normally in this mode.  You can now access Service 
     Mode by pressing the # key, the display will clear and a ' will appear. 
     Use the following procedure to program the phone: 
 
     1.  Enter 55# to access programing mode. 
 
     2.  The * key advances to the next step.  (NOTE that test mode programing 
         does NOT have step numbers, each time you press the * key the phone  
         will display the next data entry). 
 
     3.  The CLR key will revert the display to the previously stored data. 
 
     4.  The # key aborts programing at any time. 
 
     5.  To complete programing you must scroll through ALL entries until a ' 
         appears in the display. 
 
     6.  Note that some entries contain more digits than can be displayed by 
the 
         phone, in this case only the last part of the data can be seen. 
 
     TEST MODE PROGRAMING DATA: 
 
     STEP#    #OF DIGITS/RANGE    DESCRIPTION 
 
     01       00000 - 32767       SYSTEM ID 
     02       8 DIGIT BINARY      OPTION PROGRAMING, SEE NOTE 1 BELOW 
     03       10 DIGITS           MIN (AREA CODE & TEL#) 
     04       2 DIGITS            STATION CLASS MARK 
     05       2 DIGITS            ACCESS OVERLOAD CLASS 
     06       2 DIGITS            GROUP ID (10 IN USA) 
     07       6 DIGITS            SECURITY CODE 
     08       3 DIGITS            LOCK CODE 
     09       3 DIGITS            SERVICE LEVEL (LEAVE AT 004) 
     10       8 DIGIT BINARY      OPTION PROGRAMING, SEE NOTE 2 BELOW 
     11       8 DIGIT BINARY      OPTION PROGRAMING, SEE NOTE 3 BELOW 
     12       0333 OR 0334        INITIAL PAGING CHANNEL 
     13       0333                "A" SYSTEM IPCH 
     14       0334                "B" SYSTEM IPCH 
     15       3 DIGIT             NUMBER PAGING CHANNEL (021 IN USA) 
     16       8 DIGIT BINARY      OPTION PROGRAMING, SEE NOTE 4 BELOW 
 
     Steps 01 through 06 and 12 will repeat for NAM 2 if the second phone  
     number bit has been enabled in step 11. 
 
     NOTES: 
 
     Take care with Motorola's use of "0" and "1".  Some options use "0" to 
     enable, some use "1". 
 
     These are eight digit binary fields used to select the following options: 
 
     1.  (step 02 above, suggested entry is: 11101001 for "A" system, 10101001 
         for "B" sys) 
 
         Digit 1: Local use mark, 0 or 1. 
         Digit 2: Preferred system, 0 or 1. 
         Digit 3: End to end (DTMF) dialing, 1 to enable. 
         Digit 4: Not used, enter 0. 
         Digit 5: Repertory (speed) dialing, 1 to enable. 
         Digit 6: Auxiliary (horn) alert, 1 to enable. 
         Digit 7: Hands free (VSP) auto mute, 1 to enable (mutes outgoing hands 
                  free audio until the MUTE key is pressed). 
         Digit 8: Min mark, 0 or 1. 
 
     2.  (step 10 above, suggested entry is: 00000100) 
 
         Digits 1 - 4: Not used in USA, enter 0. 
         Digit 5: Single system scan, 1 to enable (scan A or B system only, 
                  determined by bit 2 of step 02. Set to "0" to allow user the 
                  option). 
         Digit 6: Super speed dial, 1 to enable (pressing N, or NN SND will  
                  dial the number stored in memory location NN). 
         Digit 7: User selectable service level, 0 to enable (allows user to  
                  set long distance/memory access dialing restrictions). 
         Digit 8: Lock function, 0 to enable (allows user to lock/un-lock the 
                  phone, if this is set to 1 the phone can not be locked). 
 
     3.  (step 11 above, suggested entry is: 00000000) 
 
         Digit 1: Handset programing, 0 to enable (allows access to programing 
                  mode without having to enter test mode). 
         Digit 2: Second phone number (not all phones), 1 to enable. 
         Digit 3: Call timer access, 0 to enable. 
         Digit 4: Auto system busy redial, 0 to enable. 
         Digit 5: Speaker disable, 1 to enable (use with select VSP units only, 
                  do not use with 2000 series mobiles). 
         Digit 6: IMTS/Cellular, 1 to enable (rarely used). 
         Digit 7: User selectable system registration, 0 to enable. 
         Digit 8: Dual antennae (diversity), 1 to enable. 
 
     4.  (step 16 above, suggested entry is: 0011010 for portable and 0011011 
         for mobile units) 
 
         Digit 1: Not used, 0 only. 
         Digit 2: Not used, 0 only 
         Digit 3: Continuous DTMF, 1 to enable (software version 8735 and 
later) 
         Digit 4: 8 hour time-out, 0 to enable (software version 8735 and 
later) 
         Digit 5: Not used, 0 only. 
         Digit 6: Failed page indicator, 0 to enable (phone beeps when an 
             incoming call is detected but signal conditions prevent 
             completion of the call). 
         Digit 7: Portable scan, 0 for portable, 1 for mobile units. 
 
 
56#  no function 
 
57x# Call Processing Mode    
                   x=0, AMPS 
                   x=1, NAMPS 
                   x=2-4, RESERVED  
                   x=5, TDMA signalling 
                   x=6, TDMA signalling with loopback before decoding 
                   x=7, TDMA signalling with loopback voice after decoding 
                   x=8, TDMA signalling with loopback FACCH after decoding 
                   x=9, TDMA forced synchronization 
 
58#  Compander On (Audio compressor and expander) (See 39#) 
 
59#  Compander Off (Audio compressor and expander) (See 38#) 
 
60#  no function 
 
61#  ESN Transfer (For Series I D.M.T./Mini TAC only) 
 
62#  Turn On Ringer Audio Path 
 
63#  Turn Off Ringer Audio Path 
 
64#-65#  no function 
 
66#  Identity Transfer (Series II Tranceivers and some Current Shipping 
Portables) 
 
67#  no function 
 
68#  Diaplay FLEX and Model Information 
 
69#  Used with Identity Transfer 
 
70#  Abbreviated field transmitter audio deviation command, for tranceivers 
     with FCC ID ABZ89FT5668. 
 
71#  Abbreviated field power adjustment command, for tranceivers with FCC ID 
     ABZ89FT5668. 
 
72#  Field audio phasing commands. 
 
73#  Field power adjustment command. 
 
74#-99# no function 
 
Notes:  There are several numbers that say "no function" next to their entry. 
        In the technical manual, those numbers APPEAR to have no function.  It  
        is very possible that they DO IN FACT have a function.  As far as I  
        know, using the information provided by the technical manual, I know  
        of no functions for these numbers.  But at the top you'll notice in the 
 
        disclaimer that NOT ALL FUNCTIONS ARE LISTED HERE.  That leaves open 
the  
        possibility of others.  Try these numbers and you may get lucky (or you 
 
        may wipe some vital information...who knows?).  I am in fact almost  
        certain that it is possible to change the ESN via the handset.  It is  
        just a matter of finding the correct combination of commands.  You can  
        bet that won't be easy, but it can't stay a secret forever though! 
 
For more information, call Motorola and order part# 68-093-00a60.  This is a  
cellular service manual that's used in their cellular service classes that  
sells for $30.  Ask for the Order Fulfillment department when ordering.  This  
manual tells it all!  An absolute must have for Motorola users. 
 
 
I think this might help.  There are some that say no function, they MIGHT. 
Case in point: 37# does something but we don't know yet...:) 
 
If I find anything else that's new, I'll post it. 
 
Catch ya later 
 
... Jesus saves lives...and redeems them for valuable prizes 
 
----------------------------------------------------------------------------- 
 Replies can be sent to: Mike.Larsen@uti.com 
 Standard disclaimer: The views of this user are strictly his/her own. 
 From UTI Systems BBS +1-815-942-2930  -  Welcome my son, to the machine.  
----------------------------------------------------------------------------- 
 
 
 
 
 
