------------------------------------------------------------------------------- UNIDEN CP-900, 1000, 1050, 1100, 1200, 1500, 1900, 2000, 3000, PRESIDENT 4000 GTS and 4500 GTS ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: UNIDEN Programmer: Serivce Handset or Programmer Handset ESN Prefix DEC: 172 HEX: AC ESN, S/N Match Required: Yes Handset Programmable: Service Handset or Programmer Handset Number of Channels: 666 (900, 1000) others 832 Programming Sequence: Connect antenna or load Power Off Disconnect standard handset Connect blue or white service handset White Handset (CP-010): Turn Power Switch On while holding * and # continue holding * and # for two seconds Blue Handset(CP-210): Turn Power Switch On Press SELECT + 2 + SEND Both Handsets: Enter step number, then data for individual parameter Press STO to enter data for each step Increment by pressing next step number To review parameters press: RCL + Step number + STO (to exit) If phone has dual NAM(ie 1050, 1500 & 2000), Press 9 + 5 + SEND (to toggle between NAMs) Press SEND to write NAM information PASS will appear in display if data is valid Step # of Digits 0 System ID: 5 XXXXX + STO 1 Local Use: 1 (0 or 1) + STO 2 MIN Opt: 1 (0 or 1) + STO 3 Mobile Number: 10 XXX-XXX-XXXX + STO 4 Initial Paging Chan: 3 (333 or 334) + STO 5 Access Overload: 2 XX + STO 6 Preferred System: 1 [0 (B) or 1 (A)] + STO 7 Group ID: 2 XX + STO 8 Local Code (1): 4 XXXX + STO 9 F5 DTMF Duration: 2 0-100ms or 1-Continous Press STO to increment to F6 or A All models Except 1500, 1900 and 4500 GTS F6 Automatic Power: 1 0=3 hrs or 1=6 hrs A Handset/Handsfree 1 0(phone auto transfers from switching H/S to H/F) OR 1(call ends when H/S is placed in cradle unless user presses RCL + 6 + 6) Press STO after entering F6 or A data Press SEND to exit program mode Horn Alert: RCL + 9 + 9 + Turn Ignition Off New Unlock Code: NAM System Select: X + STO + 8 + 8 X=1 A only X=2 B only X=3 Home X=4 Standard AB or BA X=5 Inverted BA or AB ------------------------------------------------------------------------------- UNIDEN 5000 and 6000 GTS Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: UNIDEN Programmer: Program or Service Handset with CP 505 Adaptor ESN Prefix DEC: 172 HEX: AC ESN, S/N Match Required: Yes Stamped Model Number: 5000 or 6000 GTS Number of Channels: 832 Programming Sequence: Power Off Remove Battery and install CP505 or CP505A adaptor Connect CP505(A) to power supply or to CP 504 battery eliminator per adaptor instructions Connect Program Handset to CP 505(A) adaptor White Handset (CP-010): Turn Power Switch On while holding * and # continue holding * and # for two seconds Blue Handset(CP-210): Turn Power Switch On Press SELECT + 2 + SEND Both Handsets: Enter step number, then data for individual parameter Press STO to enter data for each step Increment by pressing next step number To review parameters press: RCL + Step number + STO (to exit) To select Alternate NAM, Press 1 + STO + 90 (NAM 1) or 2 + STO + 90 (NAM 2) Press SEND to write NAM information PASS will appear in display if data is valid Step # of Digits 0 System ID: 5 XXXXX + STO 1 Local Use: 1 (0 or 1) + STO 2 MIN Opt: 1 (0 or 1) + STO 3 Mobile Number: 10 XXX-XXX-XXXX + STO 4 Initial Page Channel: 3 (333 or 334) + STO 5 Access Overload: 2 XX + STO 6 Preferred System: 1 [0 (B) or 1 (A)] + STO 7 Group ID: 2 XX + STO 8 Lock code (1): 4 XXXX + STO 9 Options F5 DTMF Duration: 1 0 - Continuous 1 - 100 ms Press STO to program phone New Unlock Code: RCL + 70 + Current 4 digit Unlock code + new 4 digit Unlock code System Select: X + STO + 8 + 8 X=1 A only X=2 B Only X=3 Home X=4 Standard AB or BA X=5 Inverted BA or AB ------------------------------------------------------------------------------- UNIDEN CP-5500 Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: UNIDEN Programmer: Keypad ESN Prefix DEC: 172 HEX: AC ESN, S/N Match Required: Yes Stamped Model Number: CP-5500 Number of Channels: 832 Programming Sequence: Install fully charged battery Power On Select NAM NAM 1: 1 + STO + 90 NAM 2: 2 + STO + 90 Power Off Press PWR key while holding * and # Continue holding * and # for four seconds "Roam.No Svc.In Use& M" lights will display Release * and # keys Enter sequence 32218591 (within 7 seconds) SID will display Enter Step number, then data for individual parameter Press STO to enter data for each step (ie to enter System ID, press 0+XXXXX+STO) Increment by pressing next step number To review parameters press: RCL + step number + STO (to exit) Press SEND to write NAM information PASS will appear in display if data is valid Press END to exit program mode Step # of Digits 0 System ID: 5 XXXXX + STO 1 Local Use: 1 (0 or 1) + STO 2 MIN Opt: 1 (0 or 1) + STO 3 Mobile Number: 10 XXX-XXX-XXXX + STO 4 Initial Page Channel: 3 [333 or 334] + STO 5 Access Overload: 2 XX + STO 6 Preferred System: 1 [9 (B) or 1 (A)] + STO Note 1: Step number will not display when entering mobile number) 7 Group ID: 2 XX + STO 8 Lock Code: 4 XXXX + STO 9 DTMF Duration: 1 0 - 100 ms or 1 - Continuous Press STO after entering Step 9 Press SEND to write data Press END to exit program mode New Program code: RCL + 70 + Current 4-digit Program Lock Code (Preset 0000) + new 4 digit program code + STO + END New Unlock Code: RCL + 70 + 4 digit program Lock Code (Preset 0000) + SEND + New 4 digit Unlock Code (Preset 0123) + STO + END System Select: X + STO + 8 + 8 X=1 A Only X=2 B Only X=3 Home X=4 Standard AB or BA X=5 Inverted BA or AB X=6 System ID (*) (*) To set System ID: CLR + 5 digit System ID + STO + 72 To view current System Select Setting: RCL + 88