Sony CMH-333 NAM Programming instructions:
------------------------------------------


Programming mode:

1)  Turn on phone

2) Enter the password "76692643" within 10 seconds after "on" has
appeared on the display.

The display will read:
"n1-1 n2-2"
n1-1= NAM 1
n2-2= NAM 2

3) Select the NAM you wish to program by entering 1 or 2 on the
keypad.

The display will read:
Ab-1 Fu-2
Ab-1 = Abbreviated programming mode.  Allows you to enter the first
five (1-5) programming parameters.

Fu-2 = Full programming mode.  Allows entering all 14 parameters.

4) Select 1 or 2 on the keypad for Abbreviated or Full programming
mode.



Clearing a NAM:

Clearing the NAM results in the seventh digit of the MIN programming
parameter being changed to a line mark.  This is equivalent to there being
no number in the parametr.  All other programming parameters remain the same.
If the NAM is cleared the user will not be allowed access to it by the RCL 5
key sequence.  (refer to the owners manual)

After you have have selected the NAM in programming mode, the display
will read Ab-1 Fu-2.  Press the SEND key.  The display will read
"clear 1" or "clear 2".  The phone will then restart.



Key functions:

Power - exit programming mode without storing new data in NAM
END - Exit programming mode wil storing new data in NAM
RCL - Go back to the previous parameter
STO - Got to the next parameter



ESN:

The esn is located under the batter in the battery compartment.
It is obtained by adding 1540 to the front of the 7 digit serial
number.



Programming Steps:

Display	Description    	   Possible Entries   Default     Digits  Press
1	System ID of home   00000 to 32767	00000	    5	  STO
        mobile service area

2  Area Code & phone numb.  0000000001-  	1231234567  10    STO
			    9999999999

3 Area Code (used when      000-999		123	    3     STO
  calling own phone numb.


4 IPCH (inital paging       0000 - 9999		0333        4     STO
  channels in home
  service area)


5 PS (preferred system)	    1=A 0=B             1           1     STO (full)
                                                                  END (Abbrev)

6  Options:		    0000000 - 1000110   100010      7bits  STO
   A: Call Timer Display    ABCDEFG
                            A: 0=deactivate displ.
                               1=activate displ

   B: Reserved              B: Set to 0
   C: Reserved              C: set to 0
   D: Reserved              D: set to 0
   E: Caller timer          E: 0=out & in 
      counts outgoing &        1=out only
      incoming calls
   F: Call Timers           F: 0=deactivate
                               1=activate call
                                  timers

7 RH Roam Inhibit	    0=roam allowed       0          1       STO
                            1=roam inhibit


8 Local Use Mark            0=Disabled           1          1       STO
                            1=Enabled

9 MIN (mobile ID number)    Set to 1             1          1       STO

10 SCM (Station Class       Set to 1110         1110        4bits   STO
   Mark)

11 Initial Dedicated        Set to 0333         0333        4       STO
   Control Channel for
   System A

12 Initial Dedicated        Set to 0334         0334        4       STO
   Control Channel for
   System B


13 GIM Group ID Mark        00-15               00          2       STO

14 ACCOLC  Access Overload  00 to 09            07          2       END
   Class (0+last digit of                                           (store & exit)
   phone number)



-end