------------------------------------------------------------------------------- OKI CS1 ------------------------------------------------------------------------------- NAM Type: Tri-State Manufacturer: OKI Programmer: Motorola 1801 or Curtis ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes, (after date code 427A XXXX) (427=Week 27 of 1984) Programmable Handset: No Available Channels: 666 Phone Number Format: XXX-XXX-XXXX Lock Code Format: XXX MIN Option: Enabled Repertory Option: Enabled Handsfree Option: Disabled (Enabled if equipped) Local Ude Option: Enabled End-to-End Signalling: Enabled Horn Alert Option: Enabled System ID Format: XXXXX Preferred System: A or B Access Overload Class: XX Group ID Format: XX Initial Paging Channel: 333 or 334 Station Class: 00 Hex Address B7 B0 13 0 0 0 0 X X X 1 Hex Address 13 - B0 Call Timer B1 Total Lock B2 Home System Only B3 Manual System Select Horn Select: HORN New Unlock Code: NAM System Select: N/A ------------------------------------------------------------------------------- OKI 21 & 23 ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Number of Channels: 832 Programming Sequence: Step #1 First Time Program Only Program Dealer Password Power On Press * and # simultaneously-then release Enter the first time password: *12345678# Display will show "enter PW-STO" Enter New 10 digit password + STO (recommend 1234567890) Display will show "re-enter PW-STO" Re-Enter 10 digit password (1234567890) + STO This step restricts programming by those not aware of current password Step #2 Programming New or Used Phone Power On Press STO and RCL (Simulatneously) Release Enter password within 30 seconds of Power On (see first time Program info) Software Version and ESN will display Press CLR to enter program mode Initialize Phone (0+0, "Cleared" will appear) Enter Step number 1-9 and the parameters info for that step After entering each step. Press STO to enter data NAM contents may be scrolled with the Volume Up and DOWN keys Press CLR to exit programming mode. # of digits Mobile Number: 10 XXX-XXX-XXXX + STO System ID: 5 XXXXX + STO Initial Paging Channel: 4 0333 or 0334 + STO Access Overlaod: 2 XX + STO Lock Code: 4 XXXX + STO Group ID: 2 XX + STO Station Class: 4 1000 + STO Options(1): 4 11X0 + STO Security Code: 6 XXXXXX + STO (1) Options MIN Opt Local Use Handsfree Spare 1 1 0 or 1 0 OKI 21 Phone Operation Horn Alert: N/A New Unlock Code: FUNC + 18 + 6 digit security code (NAM) (Current Unlock Code will Display) + New 4 digit Unlock Code + STO System Select: FUNC + 2 + 6 digit security code (current System setting displays) + 2 + 2 + 2 etc.. (to scroll choices) + STO to enter selection AB or BA A only B only Home Only SID Press STO to enter selection OKI 23 Phone Operation Horn Alert: Menu (3 times) (Until "Review & Set" Displays) + 0 ("Unlock Code Set" displays) + 6 digit security code (Current Unlock Code Displays) + New 4 digit Unlock Code + STO System Select: MENU (3 times) (Until "Review & Set" Displays) + 3 (Current System Setting will display) + RCL + RCL + RCL (to Scroll Choices) + STO (To enter Selection) AB or BA A Only B Only Home Only SId Press STO to enter selection ------------------------------------------------------------------------------- OKI 200, 300 & 400 SERIES (*) MANUFACTURED BEFORE JANUARY 1, 1989 (*) ------------------------------------------------------------------------------- NAM Type: Tri-State Manufacturer: OKI Programmer: Motorola 1801 - CELNAM, Curtis or Bytek ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Handset Programmable: No Number of channels: 666 (OKI-400 has 832) Phone Number: XXX-XXX-XXXX Lock Code: XXX MIN Option: Enabled Repertory Option: Enabled Handsfree: Disabled (Enable if Equipped) Local Use: Enabled End-to-End Signalling: Enabled Horn Alert: Enabled System ID: XXXXX Preferred System: A or B Access Overload: XX Group ID: XX Initial Paging Channel: 333 or 334 Station Class: XX These series of phones must be initialized after programmig and prior to being placed in service. To initialize phone follow the steps listed: OKI CDL 201/240: FCN + 9 + 9 + Lock Code + 0 + * All other units: FCN + 9 + 9 + * + Last 8 digits of Mechanical Serial # + * Pre 811 or 903 software (for 400 series). If phone has later software, see OKI 400 Series handset programming instructions. Horn Alert: OKI 201 Set- FCN + 91 + * Clear- FCN + 91 + # OKI-Portable: N/A OKI-210, 230, 410, 420, 430, 440, 450, 490 Set- FCN + 50 + * Clear- FCN + 50 + # New Unlock Code: OKI 201, 210, 240, 410, 420, 440, 450 & 490: NAM OKI 230, 300 Portable and 430: FCN + 04 + * + Current Unlock Code (NAM) + New Unlock Code (8 digits max) System Select: OKI 201 & 240 FCN + 01 + Unlock Code + X + * X=0 Standard (AB or BA) X=1 Alternate (BA or AB) X=2 A Only X=3 B Only X=4 Home OKI 210, 230, 410, 420, 430, 440, 450, 490 FCN + 01 + * + RCL + RCL + RCL (to scroll options) Options include: STD AB or STD BA SCN BA or SCN AB SCN A SCN B SCN HO Press * to enter selection or CLR to exit without changing sel ------------------------------------------------------------------------------- OKI 400 SERIES - WITH 811, 903, or 905 SOFTWARE ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Handset Programmable: Yes Number of Channels: 666 (811 software) or 832 (903, 904, 905 software) Programming Sequence: Power On Enter Sequence END + RCL + FCN + CLR + SND Enter Code: 08693427 (Software 811 or 903) or Enter Code: 39061875 (Software 904 or 905) (904/905 used in CHEVROLET Transportable) Code must be entered within 10 seconds of power on CLR can be used to erase a mistake in input After inputting data for a specific location, press # to enter, then press * to increment Press END to write NAM information # of Digits Mobile Number: 10 XXX-XXX-XXXX + # + * System ID: 5 XXXXX + # + * Initial Paging Channel: 4 0333 or 0334 + # + * Access Overload: 2 XX + # + * Lock Code: 3-4 XXX or XXXX + # + * Group ID: 2 XX + # + * Station Class: 4 0000 (811 software) or 1000 + # + * Option Bits: 4 11XX + # + * Option Bits; MIN Option Local Use Handsfree Horn Alert 1 1 0 or 1 0 or 1 Some of the models with this software were still equipped with NAM socket. Do _NOT_ attemp to program phone with a NAM if the phone has a 811, 903, 904, or 905 software Horn Alert: FUNC + 50 + * (Activate) FUNC + 50 + # (Deactivate) New Unlock Code: NAM (Most Models) OKI 430: FUNC + 04 + * + 3-4 digit security code System Select: FUNC + 01 + * + RCL + RCL + RCL (Continue pressing RCL until one of the following prompts appears) SCAN BA, SCAN AB, SCAN A, SCAN B, HOME, ENTER SID (430 ONLY) Press * to enter selection and CLR to exit function ------------------------------------------------------------------------------- OKI 610, 630, 691 Transportable & 692 Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Handset Programmable: Yes Number of Channels: 832 Programming Sequence: Power Off Power On Press and hold two keys simultaneously once wake up tone has stopped Use RCL and MENU for 630 and 692 Use any two number keys for 610 and 691 Release depressed keys and enter Password-0008693427 Software Version and ESN will display press CLR to enter Program mode Enter Step Number (1 to 9) then enter data Press * (610 & 691) or STORE (630 & 692) to enter each step. Once Data has been entered, the NAM information can be scrolled with the Vol UP or DN key Press CLR + CLR to write NAM information # of Digits Mobile Number 1: 10 XXX-XXX-XXXX System ID 1: 5 XXXXX Initial Paging Channel: 3 XXX 1 Press * to program 2nd Number (630 and 692 models) * Mobile Number 2: 10 XXX-XXX-XXXX * System ID 2: 5 XXXXX * Initial Page Channel: 3 XXX Access Overload: 2 XX Lock Code: 4 XXXX Group ID: 2 XX Station Class(4): 4 1000 Options(3): 4 11X1 Security Code: 6 XXXXXX (3) Options... MIN Option Local Use Handsfree Horn Alert 0=Disable 1 1 0 or 1 1 1=Enable (4) Enter Station Class In Binary (1000 Binary = 08 Dec) New Unlock Code: FUNC + 92 + 6 digit Security Code (NAM) + New 4 digit Unlock Code + * System Select: FUNC + 3 + 3 + 3 etc... (to scroll thru selection) SCN AB SCN BA SCN A SCN B SCN HO Press * to enter selection ------------------------------------------------------------------------------- OKI 620 & 693 Transportable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Handset Programmable: Yes Number of Channels: 832 Programming Sequence: Power Off Power On After wake up tone has stopped, press and hold the RCL and DUNC keys simultaneously Release depressed keys and enter password: 0008693427 Software Version and ESN will display Press CLR to enter Program Mode Enter Step Number (1 to 9) then thru data Press STO to enter each step Once data has been entered, the NAM information can be scrolled with the VOL UP or DN key press CLR + CLR to write NAM information # of Digits Mobile Number 1: 10 XXX-XXX-XXXX + STO + VOL DN System ID 1: 5 XXXXX + STO + VOL DN Initial Paging: 3 XXX + STO + VOL DN PRESS * to program 2nd NAM *Mobile Number 2: 10 XXX-XXX-XXXX + STO + VOL DN *Systen ID 2: 5 XXXXX + STO + VOL DN *Init Pag Chan 2: 3 XXX + STO + VOL DN Access Overload: 2 XX + STO + VOL DN Lock Code: 4 XXXX + STO + VOL DN Station Class(4): 4 1000 + STO + VOL DN Options(3): 4 11X1 + STO + VOL DN Security Code: 6 XXXXXX + STO + VOL DN (3) Options Step- MIN Option Local Use Handsfree Horn Alert 1 1 0 or 1 1 (4) Enter Station Class in Binary (1000 binary = 08 decimal) New Unlock Code: FUNC + 92 + 6 digit security code (NAM) + New 4 digit Unlock Code + STO System Select: FUNC + 3 + 3 + 3 + etc... (to scroll thru selections) SCN AB SCN BA SCN A SCN B SCN HOME Press STO to enter selection ------------------------------------------------------------------------------- OKI 700 Portable & ACC91 ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Keypad ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Handset Programmable: Yes Number of Channels: 832 Programming Sequence: Power On (wait for beep) Press MENU and RCL simulatenously Enter code 0008693427 ESN will appear in HEX and Software Version Press CLR to enter Program Mode Continue to next step for NAM #1 or Press * to program #2 Press STO to store data for each step Press CLR + CLR to write NAM information # of Digits Mobile Number 1: 10 XXX-XXX-XXXX + STO System ID 1: 5 XXXXX + STO Initial Page Channel 1: 3 XXX + STO Access Overload: 2 XX + STO Lock Code: 4 XXXX + STO Group ID: 2 XX + STO Station Class(1): 4 1000 (ACC91) + STO 1010 (700 Port) + STO Options(2): 4 XXXX + STO Security Code: 6 XXXXX + STO New Unlock Code: MENU + Vol Up or Down keys until "Unlock Code Set" appears Enter 6 digit Security code + new 1-8 digit unlock code + STO System Select: MENU + Vol Up or Down keys until "System" displays. Repeatedly press RCL to scroll selections. Prefer B Prefer A System A System B Home Only Only SID Press STO to enter selection ------------------------------------------------------------------------------- OKI 710 Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Keypad ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Number of Channels: 832 Programming Sequence: Program Dealer Password first Press * and # simultaneously then enter *12345678# Enter 10 digit dealer password (Recommened to use 1234567890) Press STO to enter password into memory Unit will request you to enter password again Enter programmed Dealer password + STO Programming the Phone: Power On Press FUNC and RCL simultaneously then release Enter Dealer Password (See Part I) (Password must be entered with 30 seconds of Power On) Software Version will display "Spd Dial Mem Clear" then "To Reset Press 0" will display Press 0 to clear memory locations (or CLR to pass this step) "Default Data Set" then "To Reset Press 0" will display Press 0 to reset phone options (or CLR to skip) "NAM 1" then "OWN#" will display After each parameter is entered, press STO to enter data then Vol Down to increment Press CLR to exit (This also allows access to NAM 2) Repeatedly press CLR to exit Program Mod # of Digits Mobile Number: 10 XXX-XXX-XXXX + STO + VOL DN System ID: 5 XXXXX + STO + VOL DN Initial Paging Channel: 4 0333 or 0334 + STO + VOL DN Access Overload: 2 XX + STO + VOL DN Unlock Code: 4 XXXX + STO + VOL DN Group ID: 2 XX + STO + VOL DN Station Class: 4 1010 (10d) + STO + VOL DN Options(1): 4 11X0 + STO + VOL DN Security Code: 6 XXXXXX + STO + VOL DN Options(1): MIN Options Local Use Handsfree Not used 1 1 0 or 1 0 New Unlock Code: FUNC + 14 + 6 digit security code (Current Unlock Code displays) + New 4 digit unlock Code + STO + CLR (to exit) System Select: FUNC + 12 + 6 digit security code + Repeatedly press 2 to scroll choices; AB BA B Only A Only Home Only SID Press STO to enter selection Press CLR (to exit) ------------------------------------------------------------------------------- OKI 750 Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Keypad ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes Number of Channels: 832 Programming Sequence: Program Dealer Password First Press * and # simultaneously then enter *12345678# Enter 10 digit Dealer password (Recommended to use 1234567890) Press STO to enter password into memory Unit will request you enter password again Enter programmed Dealer password Programming the Phone: Power On Press MENU and RCL simultaneously then release Enter Dealer Password (see above) (Password must be entered within 30 seconds of power on) Software Version and ESN will display "Spd Dial Mem Clear" then "To Reset Press 0" will display Press 0 to Clr Mem Locations (or CLR to pass this step) "Default Data Set" then "To Reset Press 0" will display "NAM 1" then "OWN#" will display After each parameter is entered, press STO to enter data then VOL DOWN to increment Press CLR to exit (this also allows access to NAMs 2-5) Repeatedly press CLR to exit Program Mode # of Digits Mobile Number: 10 XXX-XXX-XXXX + STO + VOL DN System ID: 5 XXXXX + STO + VOL DN Initial Paging channel: 4 0333 or 0334 + STO + VOL DN Access Overload: 2 XX + STO + VOL DN Unlock Code: 4 XXXX + STO + VOL DN Group ID: 2 XX + STO + VOL DN Station Class: 4 1010 (10d) Options(1): 4 11X0 + STO + VOL DN Security Code: 6 XXXXXX + STO + VOL DN (1) Options: MIN Options Local Use Handsfree Hot used 1 1 0 or 1 0 Programming Sequence (2nd NAM): Press CLR after programming NAM 1 Enter Mobile Number #2 + STO + VOL DN Enter System ID #2 + STO + VOL DN Enter Init Paging Channel #2 + STO + VOL DN Press CLR to exit and program #2 + STO + VOL DN Press CLR again to exit program mode ------------------------------------------------------------------------------- OKI 810 MOBILE AND 891 TRANSPORTABLE ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefex DEC: 129 HEX: 81 ESN, S/N Match Required: Yes (129 + 0 + Last seven digits of serial #) Stamped Model Number: UM9023 Number of Channels: 832 Programming Sequence: Power Off Power On Press and hold RCL and FUNC keys simultaneously once wake up tone has stopped Release depressed keys and enter Password *12345678# "Enter New PW & STO" will display (Recommended number (1234567890) Enter Password + STO Re-Enter Password + STO Phone automatically steps to Program mode. Programming A Used Phone: Power Off Power On Press and hold RCL andFUNC keys simultaneously once wake tone has stopped Release depressed keys and enter Password (Enter Password within 30 seconds) ESN and Serial Number will display SPD Dial displays - Press 0 to clear or CLR to increment Default Data Displays-Press 0 to clear or CLR to increment SSN Displays (N/A) Press 0 to increment "Phon" appear Enter data for each step and press STO + Vol UP or DOWN to increment Once data has been entered, the NAM information can be scrolled with the Vol UP or Down Key. Press CLR to exit Program Mode # of Digits Mobile Number: 10 XXX-XXX-XXXX System ID: 5 XXXXX Initial Paging Channel: 4 0333 or 0334 Access Overload: 2 XX Group ID: 2 XX Unlock Code: 4 XXXX Station class(4): 4 1000 Options(3): 4 1101 Security Code: 6 XXXXXX (3)Options: MIN Options Local Use Not Used Horn alert (0=Disabled) 1 1 0 1 (1=Enabled) (4) Enter Station Class in binary (1000b = 08d) New Unlock Code: FUNC + 16 + 6 digit Security Code (NAM) + New 4 digit Unlock Code + STO System Select: FUNC + 2 + 6 digit security Code + 2 + 2 + ...etc (to scroll thru selections) SCN AB SCN BA SCN A SCN B SCN Ho SID NO. (Enter System ID #) Press STO to enter selection ------------------------------------------------------------------------------- OKI 830 ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Handset ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes (129 + 00 + Last 6 digit of serial #) Stamped Model Number: UM9023 Number of Channels: 832 Program Sequence: % First Time Programming % Power Off Power On Press and hold RCL and MENU keys simultaneously once wake tone has stopped Release depressed keys and enter Password *12345678# "Enter New Pw & STO" will display (Recommeded number 1234567890) Enter Password + STO Re-enter Password + STO Phone automatically steps to Program Mode Programming Sequence: % Use Phone % Power Off Power On Press and hold RCL and MENU keys simultaneously once wake tone has stopped Release depressed keys and enter Password (Enter Password within 30 seconds) ESN and Serial Number will display SSN display (N/A) Press CLR to increment SPD Dial displays - Press * to clear or CLR to increment Default Data displays - Press * to clear or CLR to increment Power ON "Message" and "Enter Alpha" will display Press CLR to exit or enter alpha message to display during power up of phone NAM 1 program appears (Press VOL Down to select NAM 2) Enter Data for each step + STO + VOL Down to increment Once data has been entered, the NAM information can be scrolled with the VOL Up or Down Key Press CLR to exit Program mode Mobile Number: 10 XXX-XXX-XXXX System ID: 5 XXXXX Initial Paging Channel: 4 0333 or 0334 Access Overload: 2 XX Group ID: 2 XX Unlock Code: 4 XXXX Station Class(4): 4 1000 Options(3): 4 1101 Security Code: 6 XXXXXX (3) Options: MIN Options Local Use Audio Mute Horn Alert 1 1 0 1 (4) Enter Station Class in Binary (1000b = 08d) New Unlock Code: FUNC + 16 + 6 digit security code (NAM) + new 4 digit Unlock code + * System Select: MENU + or ("Until Adm. Menu" displays) + RCL + 6 digit security code + (Until Current Selection Displays) + RCL (To view choices) + STO + CLR (To Exit) For Only SID: STO + 5 digit System Identification + STO + CLR + CLR (to exit) ------------------------------------------------------------------------------- OKI 900 Portable ------------------------------------------------------------------------------- NAM Type: EEPROM Manufacturer: OKI Programmer: Keypad ESN Prefix DEC: 129 HEX: 81 ESN, S/N Match Required: Yes (129 + last 6 digit of serial #) Stamped Code Number: UM9022 Number of Channels: 832 Programming Sequence: Program Dealer Password First Press RCL and MENU keys simultaneously then enter *12345678# Enter 10 digit Dealer Password (Recommended 1234567890) Press STO to enter password into memory Unit will request you enter password again Enter programmed Dealer Password and press STO Programming the Phone Power On Press MENU and RCL simultaneously then release Enter Dealer Password (Password must be entered within 30 seconds of Power On) Software Version and ESN (In Hex) will display "Spd Dial Mem Clear" then "To Reset Press *" will display Press * to Clear Memory Locations (or CLR to pass this step) "Default Data Set" then "To Reset Press *" will display "Press * to rest phone options (or CLR to pass this step) "Power On" will display for 2 seconds then "Enter Alpha" shows. Enter 8 letters maximum then STO step to NAM programming "NAM 1" then "OWN#" will display. After each parameter is entered, press STO to enter data then VOL Down to increment Press CLR to exit (This also allows access to NAMs 2-5) Repeatedly press CLR to exit Program Mode # of Digits Mobile Number: 10 XXX-XXX-XXXX + STO + VOL Down System ID: 5 XXXXX + STO + VOL Down Initial Paging Channel: 4 0333 or 0334 + STO + VOL Down Access Overload: 2 XX + STO + VOL Down Group ID: 2 XX + STO + VOL Down Unlock Code: 4 XXXX + STO + VOL Down Station Class: 4 1010 (10d) + STO + VOL Down Options(1): 4 11X0 + STO + VOL Down Security Code: 6 XXXXXX + STO + VOL Down (1) Options: MIN Option Local Use Handsfree Not Used (0=Disabled) 1 1 0 or 1 0 (1=Enabled) % Programming NAMs 2-5 % Programming Sequence: Press CLR after Programming NAM 1 Enter Mobile Number #2 + STO + VOL Down Enter System ID #2 + STO + VOL Down Enter Intial Paging channel #2 + STO + VOL Down Enter Access Overload #2 + STO + VOL Down Enter Group ID #2 + STO + VOL Down Press CLR to exit and program NAMs #3-#5 Repeat above steps to program NAMs #3-#5 Press CLR again to exit Program Mode New Unlock Code: MENU + VOL Down + VOL Down etc... (until "Adm.Menu" displays) + RCL + 6 digit security code (NAM) + VOL Down + VOL Down + VOL Down ("Unlock Code Set" and "Current Unlock Code" will display) + Ente new 1-8 digit Unlock Code + STO + CLR (To exit) System Select: MENU + VOL Down + VOL Down + etc... (Until "Adm.Menu" displays) + RCL + 6 digit security code (NAM) + VOL Down + VOL Down (Until Current Status displays) + RCL + RCL + RCL (To scroll choices) + STO + CLR (to exit) Pref A Pref B A Only B Only Home Only SID Press STO to enter selection Press CLR to exit